bedHedd:
getting my xbox dongle working
I bought the microsoft third party adapter and got it working with steamos
getting xbox dongle working on my steam deck I got some xbox controllers and a dongle recently as I noticed that I was hitting the max pairing limit on bluetooth on my steam deck. I bought this dongle because it was small and supported by Microsoft https://www.amazon.com/dp/B0CN6HT6JZ?language=en-US In terms of setup, this guide + script was sup…
It has been a while since I last got it setup, so the arch wiki’s section on the different drivers were helpful in figuring out which packages I needed
https://wiki.archlinux.org/title/Gamepad#Xbox_Wireless_Controller_/_Xbox_One_Wireless_Controller
xpadneo
A relatively new driver which does support the Xbox One S and Xbox Series X|S controller via Bluetooth is called xpadneo . In addition to these two models, it has also basic support for the Xbox Elite Series 2 Wireless controller. In exchange for fully supporting just two controllers so far, it enables one to read out the correct battery level, supports rumble (even the one on the trigger buttons - L2/R2), corrects the (sometimes wrong) button mapping and more.
Installation is done using DKMS: xpadneo-dkms AUR .
Note Pairing a new Xbox One S controller for the first time may prove difficult, from not pairing at all to entering a connect/disconnect loop. These problems are described there . The best way to reliably pair the controller is to first pair it in Windows 10. However, this needs be done using the same Bluetooth adapter. A solution is to install a free copy of Windows 10 Evaluation on a Virtual machine (using QEMU or VirtualBox , taking care of the Bluetooth adapter passthrough requirements, e.g. as an USB device) using Arch Linux as your host, and pair in Windows 10 first, then do the same again under your Arch Linux system. Then pairing will succeed and there will be no need of further Windows 10 use.
Connect Xbox Wireless Controller with Microsoft Xbox Wireless Adapter
xone is a Linux kernel driver for Xbox One and Xbox Series X|S accessories. It serves as a modern replacement for and supersedes xpad and xow. Currently working via wired or with the Microsoft Xbox Wireless Adapter “dongle”. Bugfixes for this driver are now being mainted by the dlundqvist fork of the original driver.
Install xone-dkms AUR and, if using the wireless dongle, xone-dongle-firmware AUR . Installation requires a reboot of your system.
Note
The headers corresponding to your kernel are required; see DKMS#Installation .
The adapter uses a mt76 based 802.11/15 chipset which can result in interference with other wireless adapters connected to the same system or close by.
I needed the xpadneo and xone. While looking for relevant install configs, I came across this post which helped explain xone further
https://old.reddit.com/r/NixOS/comments/1inbiy5/getting_xbox_controllers_to_work_on_nixos/mcatp5f/
xpadneo config parameters
This post was helpful in figuring out what I needed for xpadneo to work
grnqrtr comments on Help needed to install and debug xpadneo (Xbox controller) driver
I got it working! For initial problem of controller not even showing up in a scan, I was dumb and didn’t have it in “pair” mode. I thought the flashing light meant pair mode, but I had to hold another button to get it into “pair” mode where the light flashes faster.
In case it helps anyone else, I ended up with this in my config to eventually get it to connect stably:
# Enable xbox controller
hardware.xpadneo.enable = true;
hardware.bluetooth.settings = {
General = {
Privacy = "device";
JustWorksRepairing = "always";
Class = "0x000100";
FastConnectable = true;
};
};
boot = {
extraModulePackages = with config.boot.kernelPackages; [ xpadneo ];
extraModprobeConfig = ''
options bluetooth disable_ertm=Y
'';
};
xone config
I had some issues consistently getting 4 controllers to pair with the dongle. Fortunately this config worked
samjk14 comments on anyone know how to the get the xone driver to work on nixos for a controller addapter?
This is working for me. I don’t actually know if the linux_zen bit is needed. I tried a few things and when it started working I stopped experimenting.
hardware.xone.enable = true; environment.systemPackages = with pkgs; [ linuxKernel.packages.linux_zen.xone ];
A restart was required after this.
You see the commits here
xpad neo
nix-config/machines/HT-RL06-PC/default.nix at e90c48324d45f6a585093f77fd02c24bbe053f9e · BedHedd/nix-config · GitHub
xone
nix-config/machines/HT-RL06-PC/default.nix at b6e3d7830180d051d964f4b5b40c91312e445a1b · BedHedd/nix-config · GitHub
The config worked and I had no issues with the controllers in my work area, but I kept getting controller drop outs with the dongle in the living room. I suspect the batteries were causing the drop outs, so until the replacement rechargeable batteries arrive, I looked into updating the controller firmware. I recalled that the arch wiki had this section
Note
Pairing a new Xbox One S controller for the first time may prove difficult, from not pairing at all to entering a connect/disconnect loop. These problems are described there . The best way to reliably pair the controller is to first pair it in Windows 10. However, this needs be done using the same Bluetooth adapter. A solution is to install a free copy of Windows 10 Evaluation on a Virtual machine (using QEMU or VirtualBox , taking care of the Bluetooth adapter passthrough requirements, e.g. as an USB device) using Arch Linux as your host, and pair in Windows 10 first, then do the same again under your Arch Linux system. Then pairing will succeed and there will be no need of further Windows 10 use.
learning virtualization in NixOS
The arch wiki suggested using qemu and virtualbox.
I started by adding virtualbox to my packages, but I got the following vboxdrv error:
VirtualBox kernel driver not Installed. The vboxdrv kernel module was either not loaded, /dev/vboxdrv is not set up properly, or you are using EFI Secure Boot and the module is not signed in the right way for your system. If necessary, try setting up the kernel module again by executing '/sbin/vboxconfig' as root (VERR_VM_DRIVER_NOT_INSTALLED).
Result Code:
NS_ERROR_FAILURE (0x80004005)
Component:
ConsoleWrap
Interface:
IConsole {6ac83d89-6ee7-4e33-8ae6-b257b2e81be8}
I asked chatgpt which suggested the following
You’re on NixOS, so that /sbin/vboxconfig hint from VirtualBox is not what you should run. On NixOS you fix this via config, rebuild, and making sure you’re in the right groups.
Below is the minimal checklist to get rid of VERR_VM_DRIVER_NOT_INSTALLED on NixOS.
1. Enable VirtualBox in your NixOS config
In /etc/nixos/configuration.nix (or your flake host module), add:
{ config, pkgs, ... }:
{
virtualisation.virtualbox.host = {
enable = true;
# Optional but usually needed for USB support etc.
enableExtensionPack = true;
};
# Make sure your user is in the vboxusers group
users.users.yourusername = {
isNormalUser = true;
extraGroups = [ "wheel" "vboxusers" ];
};
}
Replace yourusername with your actual user.
If you’re using Home Manager or split modules, this might live in a host module like hosts/your-machine.nix instead, but the options are the same.
2. Rebuild and switch
Run as root:
sudo nixos-rebuild switch
This will:
Build VirtualBox and the kernel modules against your current kernel.
Set up /dev/vboxdrv and friends via systemd services/udev.
3. Re-login (or reboot) so groups apply
Your user has to be in vboxusers in the current session .
Either:
# check groups
groups
If you don’t see vboxusers, log out and log back in, or reboot once:
sudo reboot
4. Verify the kernel module
After the rebuild and a fresh login:
lsmod | grep vbox
You should see something like vboxdrv, vboxnetflt, etc.
If not, check the service:
systemctl status virtualbox
On NixOS, VirtualBox auto-loads the module via services; you do not run /sbin/vboxconfig.
5. Secure Boot note (if relevant)
If you’re using Secure Boot with a custom shim, unsigned out-of-tree modules may be blocked. On NixOS, most setups either:
Run without Secure Boot, or
Use a custom signing setup for kernel modules.
If VirtualBox still fails and dmesg shows messages about module signature / Secure Boot:
Either disable Secure Boot in firmware, or
Set up module signing and include VirtualBox modules in that flow (more involved NixOS config; can go through that if you need).
Quick sanity checks
If the error persists after steps 1–4, run:
# 1) Check device
ls -l /dev/vboxdrv
# 2) Check kernel messages
dmesg | grep -i vbox
If you paste the output of those two commands plus your virtualisation.virtualbox section, I can pinpoint the exact issue.
Since chatgpt 5.1 has hallucinated more recently, I decided to look it up and found this thread
Interesting, because @dtannock it seems to work, even though it might be bad. I mean…if something has the intended effect…then it works! And, I got it to work! Here’s my config:
Interesting, because @dtannock it seems to work, even though it might be bad.
I mean…if something has the intended effect…then it works!
And, I got it to work! Here’s my config:
github.com
steam
prismlauncher #minecraft launcher
# messaging apps
# discord # i favor vesktop tbqh...
vesktop
signal-desktop
telegram-desktop
];
# virtualization
virtualisation.virtualbox.host.enable = true;
virtualisation.virtualbox.guest.enable = true;
virtualisation.virtualbox.guest.dragAndDrop = true;
users.extraGroups.vboxusers.members = [ "melty" ];
virtualisation.virtualbox.host.enableHardening = false;
# mullvad vpn
services.mullvad-vpn.enable = true;
services.mullvad-vpn.package = pkgs.mullvad-vpn;
When I launched virtuabox again, I got the following error
AMD-V is disabled in the BIOS (or by the host OS) (VERR_SVM_DISABLED).
Result Code:
NS_ERROR_FAILURE (0x80004005)
Component:
ConsoleWrap
Interface:
IConsole {6ac83d89-6ee7-4e33-8ae6-b257b2e81be8}
chatgpt recommended I enable it in my motherboard. Looking back, it must have gotten disabled when I flashed the new bios.
After enabling virtualization I got the following error:
Failed to acquire display parameter.
Unsupported resolution for screen shot: 0x0 (screen 0).
Result Code:
NS_ERROR_INVALID_ARG (0x80070057)
Component:
DisplayWrap
Interface:
IDisplay {14fd6676-ee6b-441a-988b-c83025ab693a}
At this point I decided it was more effort to setup virtualbox, so I pivoted to qemu. While reading the the nixos wiki page, I came across the section on quickemu
The wiki setup looked pretty straightforward, so I went ahead and followed the instructions
https://github.com/quickemu-project/quickemu/wiki/01-Installation#nix--nixos
The defaults worked for windows 10, but my xbox controller didn’t show up in the xbox accessories app in windows 10.
patch for windows 11
This section might be outdated, as there seems to be a new patch, but at the time of writing, the nix package hadn’t been updated
opened 10:05AM - 25 Jul 25 UTC
closed 12:25AM - 24 Jan 26 UTC
I would like to use quickemu to test some secure-boot enabled linux vms on my ub… untu host, can we please get a new release that includes updates such as #1578 and #413? =)
I decided to try again with windows 11 but I encountered some issues getting it installed to the vm
The first issue was booting into the installer.
I modified the windows-11 conf per the suggestion of this post
This is the conf that worked
#!/etc/profiles/per-user/bedhedd/bin/quickemu --vm
guest_os="windows"
disk_img="windows-11/disk.qcow2"
iso="windows-11/Win11_25H2_EnglishInternational_x64.iso"
# fixed_iso="windows-11/virtio-win.iso"
disk_size="64G"
tpm="on"
secureboot="off"
opened 03:45AM - 11 Oct 24 UTC
closed 09:33PM - 17 Oct 25 UTC
bug
good first issue
**I confirm this bug has not already been reported**
- [x] I have searched the … issues and this bug has not been reported previously
**Describe the bug**

**To Reproduce**
Steps to reproduce the behavior:
1. `quickget windows 11`
2. `quickemu --vm windows-11.conf`
3. see error
**Expected behavior**
no error
**Quickemu output**
Run `quickemu` or `quickemu` and include the output of the failure below:
<details>
<summary>Quickemu output</summary>
```text
_ _
__ _ _ _(_) ___| | _____ _ __ ___ _ _
/ _' | | | | |/ __| |/ / _ \ '_ ' _ \| | | |
| (_| | |_| | | (__| < __/ | | | | | |_| |
\__, |\__,_|_|\___|_|\_\___|_| |_| |_|\__,_|
|_| v4.9.6, using qemu 7.0.0
--------------------------------------------------------------------------------
Project - https://github.com/quickemu-project/quickemu
Discord - https://wimpysworld.io/discord
--------------------------------------------------------------------------------
Usage
quickemu --vm ubuntu.conf <arguments>
Arguments
--access : Enable remote spice access support. 'local' (default), 'remote', 'clientipaddress'
--braille : Enable braille support. Requires SDL.
--delete-disk : Delete the disk image and EFI variables
--delete-vm : Delete the entire VM and its configuration
--display : Select display backend. 'sdl' (default), 'cocoa', 'gtk', 'none', 'spice' or 'spice-app'
--fullscreen : Starts VM in full screen mode (Ctl+Alt+f to exit)
--ignore-msrs-always : Configure KVM to always ignore unhandled machine-specific registers
--kill : Kill the VM process if it is running
--offline : Override all network settings and start the VM offline
--shortcut : Create a desktop shortcut
--snapshot apply <tag> : Apply/restore a snapshot.
--snapshot create <tag> : Create a snapshot.
--snapshot delete <tag> : Delete a snapshot.
--snapshot info : Show disk/snapshot info.
--status-quo : Do not commit any changes to disk/snapshot.
--viewer <viewer> : Choose an alternative viewer. @Options: 'spicy' (default), 'remote-viewer', 'none'
--width <width> : Set VM screen width; requires '--height'
--height <height> : Set VM screen height; requires '--width'
--ssh-port <port> : Set SSH port manually
--spice-port <port> : Set SPICE port manually
--public-dir <path> : Expose share directory. @Options: '' (default: xdg-user-dir PUBLICSHARE), '<directory>', 'none'
--monitor <type> : Set monitor connection type. @Options: 'socket' (default), 'telnet', 'none'
--monitor-telnet-host <ip/host> : Set telnet host for monitor. (default: 'localhost')
--monitor-telnet-port <port> : Set telnet port for monitor. (default: '4440')
--monitor-cmd <cmd> : Send command to monitor if available. (Example: system_powerdown)
--serial <type> : Set serial connection type. @Options: 'socket' (default), 'telnet', 'none'
--serial-telnet-host <ip/host> : Set telnet host for serial. (default: 'localhost')
--serial-telnet-port <port> : Set telnet port for serial. (default: '6660')
--keyboard <type> : Set keyboard. @Options: 'usb' (default), 'ps2', 'virtio'
--keyboard_layout <layout> : Set keyboard layout: 'en-us' (default)
--mouse <type> : Set mouse. @Options: 'tablet' (default), 'ps2', 'usb', 'virtio'
--usb-controller <type> : Set usb-controller. @Options: 'ehci' (default), 'xhci', 'none'
--sound-card <type> : Set sound card. @Options: 'intel-hda' (default), 'ac97', 'es1370', 'sb16', 'usb-audio', 'none'
--sound-duplex <type> : Set sound card duplex. @Options: 'hda-micro' (default: speaker/mic), 'hda-duplex' (line-in/line-out), 'hda-
output' (output-only)
--extra_args <arguments> : Pass additional arguments to qemu
--version : Print version
```
</details>
**System information**
Run `quickreport` and include the output here; if you can't run `quickreport`,
please provide the output of the following:
<details>
<summary>Quickreport output</summary>
```text
----------------------------------
Quickemu 4.9.6
----------------------------------
Distro: Ubuntu 22.04.5 LTS
Kernel: Linux 6.8.0-45-generic x86_64
Memory: 23G
GPU:
- NVIDIA Corporation GK208B [GeForce GT 730] (rev a1)
----------------------------------
curl 7.81.0
----------------------------------
Libraries: libcurl/7.81.0 OpenSSL/3.0.2 zlib/1.2.11 brotli/1.0.9 zstd/1.4.8 libidn2/2.3.2 libpsl/0.21.0 (+libidn2/2.3.2) libssh/0.9.6/openssl/zli
b nghttp2/1.43.0 librtmp/2.3 OpenLDAP/2.5.18
Protocols: dict file ftp ftps gopher gophers http https imap imaps ldap ldaps mqtt pop3 pop3s rtmp rtsp scp sftp smb smbs smtp smtps telnet tftp
Features: alt-svc AsynchDNS brotli GSS-API HSTS HTTP2 HTTPS-proxy IDN IPv6 Kerberos Largefile libz NTLM NTLM_WB PSL SPNEGO SSL TLS-SRP UnixSocke
ts zstd
----------------------------------
QEMU 7.0.0
----------------------------------
Available CPUs:
x86 486 (alias configured by machine type)
x86 486-v1
x86 Broadwell (alias configured by machine type)
x86 Broadwell-IBRS (alias of Broadwell-v3)
x86 Broadwell-noTSX (alias of Broadwell-v2)
x86 Broadwell-noTSX-IBRS (alias of Broadwell-v4)
x86 Broadwell-v1 Intel Core Processor (Broadwell)
x86 Broadwell-v2 Intel Core Processor (Broadwell, no TSX)
x86 Broadwell-v3 Intel Core Processor (Broadwell, IBRS)
x86 Broadwell-v4 Intel Core Processor (Broadwell, no TSX, IBRS)
x86 Cascadelake-Server (alias configured by machine type)
x86 Cascadelake-Server-noTSX (alias of Cascadelake-Server-v3)
x86 Cascadelake-Server-v1 Intel Xeon Processor (Cascadelake)
x86 Cascadelake-Server-v2 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES]
x86 Cascadelake-Server-v3 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v4 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v5 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, EPT switching, XSAVES, no TSX]
x86 Conroe (alias configured by machine type)
x86 Conroe-v1 Intel Celeron_4x0 (Conroe/Merom Class Core 2)
x86 Cooperlake (alias configured by machine type)
x86 Cooperlake-v1 Intel Xeon Processor (Cooperlake)
x86 Cooperlake-v2 Intel Xeon Processor (Cooperlake) [XSAVES]
x86 Denverton (alias configured by machine type)
x86 Denverton-v1 Intel Atom Processor (Denverton)
x86 Denverton-v2 Intel Atom Processor (Denverton) [no MPX, no MONITOR]
x86 Denverton-v3 Intel Atom Processor (Denverton) [XSAVES, no MPX, no MONITOR]
x86 Dhyana (alias configured by machine type)
x86 Dhyana-v1 Hygon Dhyana Processor
x86 Dhyana-v2 Hygon Dhyana Processor [XSAVES]
x86 EPYC (alias configured by machine type)
x86 EPYC-IBPB (alias of EPYC-v2)
x86 EPYC-Milan (alias configured by machine type)
x86 EPYC-Milan-v1 AMD EPYC-Milan Processor
x86 EPYC-Rome (alias configured by machine type)
x86 EPYC-Rome-v1 AMD EPYC-Rome Processor
x86 EPYC-Rome-v2 AMD EPYC-Rome Processor
x86 EPYC-v1 AMD EPYC Processor
x86 EPYC-v2 AMD EPYC Processor (with IBPB)
x86 EPYC-v3 AMD EPYC Processor
x86 Haswell (alias configured by machine type)
x86 Haswell-IBRS (alias of Haswell-v3)
x86 Haswell-noTSX (alias of Haswell-v2)
x86 Haswell-noTSX-IBRS (alias of Haswell-v4)
x86 Haswell-v1 Intel Core Processor (Haswell)
x86 Haswell-v2 Intel Core Processor (Haswell, no TSX)
x86 Haswell-v3 Intel Core Processor (Haswell, IBRS)
x86 Haswell-v4 Intel Core Processor (Haswell, no TSX, IBRS)
x86 Icelake-Client (alias configured by machine type)
x86 Icelake-Client-noTSX (alias of Icelake-Client-v2)
x86 Icelake-Client-v1 Intel Core Processor (Icelake) [deprecated]
x86 Icelake-Client-v2 Intel Core Processor (Icelake) [no TSX, deprecated]
x86 Icelake-Client-v3 Intel Core Processor (Icelake) [no TSX, XSAVES, deprecated]
x86 Icelake-Server (alias configured by machine type)
x86 Icelake-Server-noTSX (alias of Icelake-Server-v2)
x86 Icelake-Server-v1 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v2 Intel Xeon Processor (Icelake) [no TSX]
x86 Icelake-Server-v3 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v4 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v5 Intel Xeon Processor (Icelake) [XSAVES]
x86 Icelake-Server-v6 Intel Xeon Processor (Icelake) [5-level EPT]
x86 IvyBridge (alias configured by machine type)
x86 IvyBridge-IBRS (alias of IvyBridge-v2)
x86 IvyBridge-v1 Intel Xeon E3-12xx v2 (Ivy Bridge)
x86 IvyBridge-v2 Intel Xeon E3-12xx v2 (Ivy Bridge, IBRS)
x86 KnightsMill (alias configured by machine type)
x86 KnightsMill-v1 Intel Xeon Phi Processor (Knights Mill)
x86 Nehalem (alias configured by machine type)
x86 Nehalem-IBRS (alias of Nehalem-v2)
x86 Nehalem-v1 Intel Core i7 9xx (Nehalem Class Core i7)
x86 Nehalem-v2 Intel Core i7 9xx (Nehalem Core i7, IBRS update)
x86 Opteron_G1 (alias configured by machine type)
x86 Opteron_G1-v1 AMD Opteron 240 (Gen 1 Class Opteron)
x86 Opteron_G2 (alias configured by machine type)
x86 Opteron_G2-v1 AMD Opteron 22xx (Gen 2 Class Opteron)
x86 Opteron_G3 (alias configured by machine type)
x86 Opteron_G3-v1 AMD Opteron 23xx (Gen 3 Class Opteron)
x86 Opteron_G4 (alias configured by machine type)
x86 Opteron_G4-v1 AMD Opteron 62xx class CPU
x86 Opteron_G5 (alias configured by machine type)
x86 Opteron_G5-v1 AMD Opteron 63xx class CPU
x86 Penryn (alias configured by machine type)
x86 Penryn-v1 Intel Core 2 Duo P9xxx (Penryn Class Core 2)
x86 SandyBridge (alias configured by machine type)
x86 SandyBridge-IBRS (alias of SandyBridge-v2)
x86 SandyBridge-v1 Intel Xeon E312xx (Sandy Bridge)
x86 SandyBridge-v2 Intel Xeon E312xx (Sandy Bridge, IBRS update)
x86 Skylake-Client (alias configured by machine type)
x86 Skylake-Client-IBRS (alias of Skylake-Client-v2)
x86 Skylake-Client-noTSX-IBRS (alias of Skylake-Client-v3)
x86 Skylake-Client-v1 Intel Core Processor (Skylake)
x86 Skylake-Client-v2 Intel Core Processor (Skylake, IBRS)
x86 Skylake-Client-v3 Intel Core Processor (Skylake, IBRS, no TSX)
x86 Skylake-Client-v4 Intel Core Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, no TSX]
x86 Skylake-Server (alias configured by machine type)
x86 Skylake-Server-IBRS (alias of Skylake-Server-v2)
x86 Skylake-Server-noTSX-IBRS (alias of Skylake-Server-v3)
x86 Skylake-Server-v1 Intel Xeon Processor (Skylake)
x86 Skylake-Server-v2 Intel Xeon Processor (Skylake, IBRS)
x86 Skylake-Server-v3 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v4 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v5 Intel Xeon Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, EPT switching, no TSX]
x86 Snowridge (alias configured by machine type)
x86 Snowridge-v1 Intel Atom Processor (SnowRidge)
x86 Snowridge-v2 Intel Atom Processor (Snowridge, no MPX)
x86 Snowridge-v3 Intel Atom Processor (Snowridge, no MPX) [XSAVES, no MPX]
x86 Snowridge-v4 Intel Atom Processor (Snowridge, no MPX) [no split lock detect, no core-capability]
x86 Westmere (alias configured by machine type)
x86 Westmere-IBRS (alias of Westmere-v2)
x86 Westmere-v1 Westmere E56xx/L56xx/X56xx (Nehalem-C)
x86 Westmere-v2 Westmere E56xx/L56xx/X56xx (IBRS update)
x86 athlon (alias configured by machine type)
x86 athlon-v1 QEMU Virtual CPU version 2.5+
x86 core2duo (alias configured by machine type)
x86 core2duo-v1 Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz
x86 coreduo (alias configured by machine type)
x86 coreduo-v1 Genuine Intel(R) CPU T2600 @ 2.16GHz
x86 kvm32 (alias configured by machine type)
x86 kvm32-v1 Common 32-bit KVM processor
x86 kvm64 (alias configured by machine type)
x86 kvm64-v1 Common KVM processor
x86 n270 (alias configured by machine type)
x86 n270-v1 Intel(R) Atom(TM) CPU N270 @ 1.60GHz
x86 pentium (alias configured by machine type)
x86 pentium-v1
x86 pentium2 (alias configured by machine type)
x86 pentium2-v1
x86 pentium3 (alias configured by machine type)
x86 pentium3-v1
x86 phenom (alias configured by machine type)
x86 phenom-v1 AMD Phenom(tm) 9550 Quad-Core Processor
x86 qemu32 (alias configured by machine type)
x86 qemu32-v1 QEMU Virtual CPU version 2.5+
x86 qemu64 (alias configured by machine type)
x86 qemu64-v1 QEMU Virtual CPU version 2.5+
x86 base base CPU model type with no features enabled
x86 host processor with all supported host features
x86 max Enables all features supported by the accelerator in the current host
Recognized CPUID flags:
3dnow 3dnowext 3dnowprefetch abm ace2 ace2-en acpi adx aes amd-no-ssb
amd-ssbd amd-stibp amx-bf16 amx-int8 amx-tile apic arat arch-capabilities
avic avx avx-vnni avx2 avx512-4fmaps avx512-4vnniw avx512-bf16
avx512-fp16 avx512-vp2intersect avx512-vpopcntdq avx512bitalg avx512bw
avx512cd avx512dq avx512er avx512f avx512ifma avx512pf avx512vbmi
avx512vbmi2 avx512vl avx512vnni bmi1 bmi2 bus-lock-detect cid cldemote
clflush clflushopt clwb clzero cmov cmp-legacy core-capability cr8legacy
cx16 cx8 dca de decodeassists ds ds-cpl dtes64 erms est extapic f16c
flushbyasid fma fma4 fpu fsgsbase fsrm full-width-write fxsr fxsr-opt
gfni hle ht hypervisor ia64 ibpb ibrs ibrs-all ibs intel-pt intel-pt-lip
invpcid invtsc kvm-asyncpf kvm-asyncpf-int kvm-hint-dedicated kvm-mmu
kvm-msi-ext-dest-id kvm-nopiodelay kvm-poll-control kvm-pv-eoi kvm-pv-ipi
kvm-pv-sched-yield kvm-pv-tlb-flush kvm-pv-unhalt kvm-steal-time kvmclock
kvmclock kvmclock-stable-bit la57 lahf-lm lbrv lm lwp mca mce md-clear
mds-no misalignsse mmx mmxext monitor movbe movdir64b movdiri mpx msr
mtrr nodeid-msr npt nrip-save nx osvw pae pat pause-filter pbe pcid
pclmulqdq pcommit pdcm pdpe1gb perfctr-core perfctr-nb pfthreshold pge
phe phe-en pks pku pmm pmm-en pn pni popcnt pschange-mc-no pse pse36
rdctl-no rdpid rdrand rdseed rdtscp rsba rtm sep serialize sgx sgx-debug
sgx-exinfo sgx-kss sgx-mode64 sgx-provisionkey sgx-tokenkey sgx1 sgx2
sgxlc sha-ni skinit skip-l1dfl-vmentry smap smep smx spec-ctrl
split-lock-detect ss ssb-no ssbd sse sse2 sse4.1 sse4.2 sse4a ssse3 stibp
svm svm-lock svme-addr-chk syscall taa-no tbm tce tm tm2 topoext tsc
tsc-adjust tsc-deadline tsc-scale tsx-ctrl tsx-ldtrk umip v-vmsave-vmload
vaes vgif virt-ssbd vmcb-clean vme vmx vmx-activity-hlt
vmx-activity-shutdown vmx-activity-wait-sipi vmx-apicv-register
vmx-apicv-vid vmx-apicv-x2apic vmx-apicv-xapic vmx-cr3-load-noexit
vmx-cr3-store-noexit vmx-cr8-load-exit vmx-cr8-store-exit vmx-desc-exit
vmx-encls-exit vmx-entry-ia32e-mode vmx-entry-load-bndcfgs
vmx-entry-load-efer vmx-entry-load-pat vmx-entry-load-perf-global-ctrl
vmx-entry-load-pkrs vmx-entry-load-rtit-ctl vmx-entry-noload-debugctl
vmx-ept vmx-ept-1gb vmx-ept-2mb vmx-ept-advanced-exitinfo
vmx-ept-execonly vmx-eptad vmx-eptp-switching vmx-exit-ack-intr
vmx-exit-clear-bndcfgs vmx-exit-clear-rtit-ctl vmx-exit-load-efer
vmx-exit-load-pat vmx-exit-load-perf-global-ctrl vmx-exit-load-pkrs
vmx-exit-nosave-debugctl vmx-exit-save-efer vmx-exit-save-pat
vmx-exit-save-preemption-timer vmx-flexpriority vmx-hlt-exit vmx-ins-outs
vmx-intr-exit vmx-invept vmx-invept-all-context vmx-invept-single-context
vmx-invept-single-context vmx-invept-single-context-noglobals
vmx-invlpg-exit vmx-invpcid-exit vmx-invvpid vmx-invvpid-all-context
vmx-invvpid-single-addr vmx-io-bitmap vmx-io-exit vmx-monitor-exit
vmx-movdr-exit vmx-msr-bitmap vmx-mtf vmx-mwait-exit vmx-nmi-exit
vmx-page-walk-4 vmx-page-walk-5 vmx-pause-exit vmx-ple vmx-pml
vmx-posted-intr vmx-preemption-timer vmx-rdpmc-exit vmx-rdrand-exit
vmx-rdseed-exit vmx-rdtsc-exit vmx-rdtscp-exit vmx-secondary-ctls
vmx-shadow-vmcs vmx-store-lma vmx-true-ctls vmx-tsc-offset
vmx-tsc-scaling vmx-unrestricted-guest vmx-vintr-pending vmx-vmfunc
vmx-vmwrite-vmexit-fields vmx-vnmi vmx-vnmi-pending vmx-vpid
vmx-wbinvd-exit vmx-xsaves vmx-zero-len-inject vpclmulqdq waitpkg
wbnoinvd wdt x2apic xcrypt xcrypt-en xfd xgetbv1 xop xsave xsavec
xsaveerptr xsaveopt xsaves xstore xstore-en xtpr
----------------------------------
CPU
----------------------------------
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Address sizes: 46 bits physical, 48 bits virtual
Byte Order: Little Endian
CPU(s): 20
On-line CPU(s) list: 0-19
Vendor ID: GenuineIntel
Model name: 12th Gen Intel(R) Core(TM) i7-12700
CPU family: 6
Model: 151
Thread(s) per core: 2
Core(s) per socket: 12
Socket(s): 1
Stepping: 2
CPU max MHz: 4900.0000
CPU min MHz: 800.0000
BogoMIPS: 4224.00
Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2
ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc art arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf tsc_known_f
req pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 sdbg fma cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer a
es xsave avx f16c rdrand lahf_lm abm 3dnowprefetch cpuid_fault epb ssbd ibrs ibpb stibp ibrs_enhanced tpr_shadow flexpriority ept vpid ept_ad fsg
sbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid rdseed adx smap clflushopt clwb intel_pt sha_ni xsaveopt xsavec xgetbv1 xsaves split_lock_detec
t user_shstk avx_vnni dtherm ida arat pln pts hwp hwp_notify hwp_act_window hwp_epp hwp_pkg_req hfi vnmi umip pku ospke waitpkg gfni vaes vpclmul
qdq tme rdpid movdiri movdir64b fsrm md_clear serialize pconfig arch_lbr ibt flush_l1d arch_capabilities
Virtualization: VT-x
L1d cache: 512 KiB (12 instances)
L1i cache: 512 KiB (12 instances)
L2 cache: 12 MiB (9 instances)
L3 cache: 25 MiB (1 instance)
NUMA node(s): 1
NUMA node0 CPU(s): 0-19
Vulnerability Gather data sampling: Not affected
Vulnerability Itlb multihit: Not affected
Vulnerability L1tf: Not affected
Vulnerability Mds: Not affected
Vulnerability Meltdown: Not affected
Vulnerability Mmio stale data: Not affected
Vulnerability Reg file data sampling: Mitigation; Clear Register File
Vulnerability Retbleed: Not affected
Vulnerability Spec rstack overflow: Not affected
Vulnerability Spec store bypass: Mitigation; Speculative Store Bypass disabled via prctl
Vulnerability Spectre v1: Mitigation; usercopy/swapgs barriers and __user pointer sanitization
Vulnerability Spectre v2: Mitigation; Enhanced / Automatic IBRS; IBPB conditional; RSB filling; PBRSB-eIBRS SW sequence; BHI BHI_DIS_
S
Vulnerability Srbds: Not affected
Vulnerability Tsx async abort: Not affected
```
</details>
I was able to get into the installer, but then encountered the same issue of hardware recognition
opened 03:45AM - 11 Oct 24 UTC
closed 09:33PM - 17 Oct 25 UTC
bug
good first issue
**I confirm this bug has not already been reported**
- [x] I have searched the … issues and this bug has not been reported previously
**Describe the bug**

**To Reproduce**
Steps to reproduce the behavior:
1. `quickget windows 11`
2. `quickemu --vm windows-11.conf`
3. see error
**Expected behavior**
no error
**Quickemu output**
Run `quickemu` or `quickemu` and include the output of the failure below:
<details>
<summary>Quickemu output</summary>
```text
_ _
__ _ _ _(_) ___| | _____ _ __ ___ _ _
/ _' | | | | |/ __| |/ / _ \ '_ ' _ \| | | |
| (_| | |_| | | (__| < __/ | | | | | |_| |
\__, |\__,_|_|\___|_|\_\___|_| |_| |_|\__,_|
|_| v4.9.6, using qemu 7.0.0
--------------------------------------------------------------------------------
Project - https://github.com/quickemu-project/quickemu
Discord - https://wimpysworld.io/discord
--------------------------------------------------------------------------------
Usage
quickemu --vm ubuntu.conf <arguments>
Arguments
--access : Enable remote spice access support. 'local' (default), 'remote', 'clientipaddress'
--braille : Enable braille support. Requires SDL.
--delete-disk : Delete the disk image and EFI variables
--delete-vm : Delete the entire VM and its configuration
--display : Select display backend. 'sdl' (default), 'cocoa', 'gtk', 'none', 'spice' or 'spice-app'
--fullscreen : Starts VM in full screen mode (Ctl+Alt+f to exit)
--ignore-msrs-always : Configure KVM to always ignore unhandled machine-specific registers
--kill : Kill the VM process if it is running
--offline : Override all network settings and start the VM offline
--shortcut : Create a desktop shortcut
--snapshot apply <tag> : Apply/restore a snapshot.
--snapshot create <tag> : Create a snapshot.
--snapshot delete <tag> : Delete a snapshot.
--snapshot info : Show disk/snapshot info.
--status-quo : Do not commit any changes to disk/snapshot.
--viewer <viewer> : Choose an alternative viewer. @Options: 'spicy' (default), 'remote-viewer', 'none'
--width <width> : Set VM screen width; requires '--height'
--height <height> : Set VM screen height; requires '--width'
--ssh-port <port> : Set SSH port manually
--spice-port <port> : Set SPICE port manually
--public-dir <path> : Expose share directory. @Options: '' (default: xdg-user-dir PUBLICSHARE), '<directory>', 'none'
--monitor <type> : Set monitor connection type. @Options: 'socket' (default), 'telnet', 'none'
--monitor-telnet-host <ip/host> : Set telnet host for monitor. (default: 'localhost')
--monitor-telnet-port <port> : Set telnet port for monitor. (default: '4440')
--monitor-cmd <cmd> : Send command to monitor if available. (Example: system_powerdown)
--serial <type> : Set serial connection type. @Options: 'socket' (default), 'telnet', 'none'
--serial-telnet-host <ip/host> : Set telnet host for serial. (default: 'localhost')
--serial-telnet-port <port> : Set telnet port for serial. (default: '6660')
--keyboard <type> : Set keyboard. @Options: 'usb' (default), 'ps2', 'virtio'
--keyboard_layout <layout> : Set keyboard layout: 'en-us' (default)
--mouse <type> : Set mouse. @Options: 'tablet' (default), 'ps2', 'usb', 'virtio'
--usb-controller <type> : Set usb-controller. @Options: 'ehci' (default), 'xhci', 'none'
--sound-card <type> : Set sound card. @Options: 'intel-hda' (default), 'ac97', 'es1370', 'sb16', 'usb-audio', 'none'
--sound-duplex <type> : Set sound card duplex. @Options: 'hda-micro' (default: speaker/mic), 'hda-duplex' (line-in/line-out), 'hda-
output' (output-only)
--extra_args <arguments> : Pass additional arguments to qemu
--version : Print version
```
</details>
**System information**
Run `quickreport` and include the output here; if you can't run `quickreport`,
please provide the output of the following:
<details>
<summary>Quickreport output</summary>
```text
----------------------------------
Quickemu 4.9.6
----------------------------------
Distro: Ubuntu 22.04.5 LTS
Kernel: Linux 6.8.0-45-generic x86_64
Memory: 23G
GPU:
- NVIDIA Corporation GK208B [GeForce GT 730] (rev a1)
----------------------------------
curl 7.81.0
----------------------------------
Libraries: libcurl/7.81.0 OpenSSL/3.0.2 zlib/1.2.11 brotli/1.0.9 zstd/1.4.8 libidn2/2.3.2 libpsl/0.21.0 (+libidn2/2.3.2) libssh/0.9.6/openssl/zli
b nghttp2/1.43.0 librtmp/2.3 OpenLDAP/2.5.18
Protocols: dict file ftp ftps gopher gophers http https imap imaps ldap ldaps mqtt pop3 pop3s rtmp rtsp scp sftp smb smbs smtp smtps telnet tftp
Features: alt-svc AsynchDNS brotli GSS-API HSTS HTTP2 HTTPS-proxy IDN IPv6 Kerberos Largefile libz NTLM NTLM_WB PSL SPNEGO SSL TLS-SRP UnixSocke
ts zstd
----------------------------------
QEMU 7.0.0
----------------------------------
Available CPUs:
x86 486 (alias configured by machine type)
x86 486-v1
x86 Broadwell (alias configured by machine type)
x86 Broadwell-IBRS (alias of Broadwell-v3)
x86 Broadwell-noTSX (alias of Broadwell-v2)
x86 Broadwell-noTSX-IBRS (alias of Broadwell-v4)
x86 Broadwell-v1 Intel Core Processor (Broadwell)
x86 Broadwell-v2 Intel Core Processor (Broadwell, no TSX)
x86 Broadwell-v3 Intel Core Processor (Broadwell, IBRS)
x86 Broadwell-v4 Intel Core Processor (Broadwell, no TSX, IBRS)
x86 Cascadelake-Server (alias configured by machine type)
x86 Cascadelake-Server-noTSX (alias of Cascadelake-Server-v3)
x86 Cascadelake-Server-v1 Intel Xeon Processor (Cascadelake)
x86 Cascadelake-Server-v2 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES]
x86 Cascadelake-Server-v3 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v4 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v5 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, EPT switching, XSAVES, no TSX]
x86 Conroe (alias configured by machine type)
x86 Conroe-v1 Intel Celeron_4x0 (Conroe/Merom Class Core 2)
x86 Cooperlake (alias configured by machine type)
x86 Cooperlake-v1 Intel Xeon Processor (Cooperlake)
x86 Cooperlake-v2 Intel Xeon Processor (Cooperlake) [XSAVES]
x86 Denverton (alias configured by machine type)
x86 Denverton-v1 Intel Atom Processor (Denverton)
x86 Denverton-v2 Intel Atom Processor (Denverton) [no MPX, no MONITOR]
x86 Denverton-v3 Intel Atom Processor (Denverton) [XSAVES, no MPX, no MONITOR]
x86 Dhyana (alias configured by machine type)
x86 Dhyana-v1 Hygon Dhyana Processor
x86 Dhyana-v2 Hygon Dhyana Processor [XSAVES]
x86 EPYC (alias configured by machine type)
x86 EPYC-IBPB (alias of EPYC-v2)
x86 EPYC-Milan (alias configured by machine type)
x86 EPYC-Milan-v1 AMD EPYC-Milan Processor
x86 EPYC-Rome (alias configured by machine type)
x86 EPYC-Rome-v1 AMD EPYC-Rome Processor
x86 EPYC-Rome-v2 AMD EPYC-Rome Processor
x86 EPYC-v1 AMD EPYC Processor
x86 EPYC-v2 AMD EPYC Processor (with IBPB)
x86 EPYC-v3 AMD EPYC Processor
x86 Haswell (alias configured by machine type)
x86 Haswell-IBRS (alias of Haswell-v3)
x86 Haswell-noTSX (alias of Haswell-v2)
x86 Haswell-noTSX-IBRS (alias of Haswell-v4)
x86 Haswell-v1 Intel Core Processor (Haswell)
x86 Haswell-v2 Intel Core Processor (Haswell, no TSX)
x86 Haswell-v3 Intel Core Processor (Haswell, IBRS)
x86 Haswell-v4 Intel Core Processor (Haswell, no TSX, IBRS)
x86 Icelake-Client (alias configured by machine type)
x86 Icelake-Client-noTSX (alias of Icelake-Client-v2)
x86 Icelake-Client-v1 Intel Core Processor (Icelake) [deprecated]
x86 Icelake-Client-v2 Intel Core Processor (Icelake) [no TSX, deprecated]
x86 Icelake-Client-v3 Intel Core Processor (Icelake) [no TSX, XSAVES, deprecated]
x86 Icelake-Server (alias configured by machine type)
x86 Icelake-Server-noTSX (alias of Icelake-Server-v2)
x86 Icelake-Server-v1 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v2 Intel Xeon Processor (Icelake) [no TSX]
x86 Icelake-Server-v3 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v4 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v5 Intel Xeon Processor (Icelake) [XSAVES]
x86 Icelake-Server-v6 Intel Xeon Processor (Icelake) [5-level EPT]
x86 IvyBridge (alias configured by machine type)
x86 IvyBridge-IBRS (alias of IvyBridge-v2)
x86 IvyBridge-v1 Intel Xeon E3-12xx v2 (Ivy Bridge)
x86 IvyBridge-v2 Intel Xeon E3-12xx v2 (Ivy Bridge, IBRS)
x86 KnightsMill (alias configured by machine type)
x86 KnightsMill-v1 Intel Xeon Phi Processor (Knights Mill)
x86 Nehalem (alias configured by machine type)
x86 Nehalem-IBRS (alias of Nehalem-v2)
x86 Nehalem-v1 Intel Core i7 9xx (Nehalem Class Core i7)
x86 Nehalem-v2 Intel Core i7 9xx (Nehalem Core i7, IBRS update)
x86 Opteron_G1 (alias configured by machine type)
x86 Opteron_G1-v1 AMD Opteron 240 (Gen 1 Class Opteron)
x86 Opteron_G2 (alias configured by machine type)
x86 Opteron_G2-v1 AMD Opteron 22xx (Gen 2 Class Opteron)
x86 Opteron_G3 (alias configured by machine type)
x86 Opteron_G3-v1 AMD Opteron 23xx (Gen 3 Class Opteron)
x86 Opteron_G4 (alias configured by machine type)
x86 Opteron_G4-v1 AMD Opteron 62xx class CPU
x86 Opteron_G5 (alias configured by machine type)
x86 Opteron_G5-v1 AMD Opteron 63xx class CPU
x86 Penryn (alias configured by machine type)
x86 Penryn-v1 Intel Core 2 Duo P9xxx (Penryn Class Core 2)
x86 SandyBridge (alias configured by machine type)
x86 SandyBridge-IBRS (alias of SandyBridge-v2)
x86 SandyBridge-v1 Intel Xeon E312xx (Sandy Bridge)
x86 SandyBridge-v2 Intel Xeon E312xx (Sandy Bridge, IBRS update)
x86 Skylake-Client (alias configured by machine type)
x86 Skylake-Client-IBRS (alias of Skylake-Client-v2)
x86 Skylake-Client-noTSX-IBRS (alias of Skylake-Client-v3)
x86 Skylake-Client-v1 Intel Core Processor (Skylake)
x86 Skylake-Client-v2 Intel Core Processor (Skylake, IBRS)
x86 Skylake-Client-v3 Intel Core Processor (Skylake, IBRS, no TSX)
x86 Skylake-Client-v4 Intel Core Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, no TSX]
x86 Skylake-Server (alias configured by machine type)
x86 Skylake-Server-IBRS (alias of Skylake-Server-v2)
x86 Skylake-Server-noTSX-IBRS (alias of Skylake-Server-v3)
x86 Skylake-Server-v1 Intel Xeon Processor (Skylake)
x86 Skylake-Server-v2 Intel Xeon Processor (Skylake, IBRS)
x86 Skylake-Server-v3 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v4 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v5 Intel Xeon Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, EPT switching, no TSX]
x86 Snowridge (alias configured by machine type)
x86 Snowridge-v1 Intel Atom Processor (SnowRidge)
x86 Snowridge-v2 Intel Atom Processor (Snowridge, no MPX)
x86 Snowridge-v3 Intel Atom Processor (Snowridge, no MPX) [XSAVES, no MPX]
x86 Snowridge-v4 Intel Atom Processor (Snowridge, no MPX) [no split lock detect, no core-capability]
x86 Westmere (alias configured by machine type)
x86 Westmere-IBRS (alias of Westmere-v2)
x86 Westmere-v1 Westmere E56xx/L56xx/X56xx (Nehalem-C)
x86 Westmere-v2 Westmere E56xx/L56xx/X56xx (IBRS update)
x86 athlon (alias configured by machine type)
x86 athlon-v1 QEMU Virtual CPU version 2.5+
x86 core2duo (alias configured by machine type)
x86 core2duo-v1 Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz
x86 coreduo (alias configured by machine type)
x86 coreduo-v1 Genuine Intel(R) CPU T2600 @ 2.16GHz
x86 kvm32 (alias configured by machine type)
x86 kvm32-v1 Common 32-bit KVM processor
x86 kvm64 (alias configured by machine type)
x86 kvm64-v1 Common KVM processor
x86 n270 (alias configured by machine type)
x86 n270-v1 Intel(R) Atom(TM) CPU N270 @ 1.60GHz
x86 pentium (alias configured by machine type)
x86 pentium-v1
x86 pentium2 (alias configured by machine type)
x86 pentium2-v1
x86 pentium3 (alias configured by machine type)
x86 pentium3-v1
x86 phenom (alias configured by machine type)
x86 phenom-v1 AMD Phenom(tm) 9550 Quad-Core Processor
x86 qemu32 (alias configured by machine type)
x86 qemu32-v1 QEMU Virtual CPU version 2.5+
x86 qemu64 (alias configured by machine type)
x86 qemu64-v1 QEMU Virtual CPU version 2.5+
x86 base base CPU model type with no features enabled
x86 host processor with all supported host features
x86 max Enables all features supported by the accelerator in the current host
Recognized CPUID flags:
3dnow 3dnowext 3dnowprefetch abm ace2 ace2-en acpi adx aes amd-no-ssb
amd-ssbd amd-stibp amx-bf16 amx-int8 amx-tile apic arat arch-capabilities
avic avx avx-vnni avx2 avx512-4fmaps avx512-4vnniw avx512-bf16
avx512-fp16 avx512-vp2intersect avx512-vpopcntdq avx512bitalg avx512bw
avx512cd avx512dq avx512er avx512f avx512ifma avx512pf avx512vbmi
avx512vbmi2 avx512vl avx512vnni bmi1 bmi2 bus-lock-detect cid cldemote
clflush clflushopt clwb clzero cmov cmp-legacy core-capability cr8legacy
cx16 cx8 dca de decodeassists ds ds-cpl dtes64 erms est extapic f16c
flushbyasid fma fma4 fpu fsgsbase fsrm full-width-write fxsr fxsr-opt
gfni hle ht hypervisor ia64 ibpb ibrs ibrs-all ibs intel-pt intel-pt-lip
invpcid invtsc kvm-asyncpf kvm-asyncpf-int kvm-hint-dedicated kvm-mmu
kvm-msi-ext-dest-id kvm-nopiodelay kvm-poll-control kvm-pv-eoi kvm-pv-ipi
kvm-pv-sched-yield kvm-pv-tlb-flush kvm-pv-unhalt kvm-steal-time kvmclock
kvmclock kvmclock-stable-bit la57 lahf-lm lbrv lm lwp mca mce md-clear
mds-no misalignsse mmx mmxext monitor movbe movdir64b movdiri mpx msr
mtrr nodeid-msr npt nrip-save nx osvw pae pat pause-filter pbe pcid
pclmulqdq pcommit pdcm pdpe1gb perfctr-core perfctr-nb pfthreshold pge
phe phe-en pks pku pmm pmm-en pn pni popcnt pschange-mc-no pse pse36
rdctl-no rdpid rdrand rdseed rdtscp rsba rtm sep serialize sgx sgx-debug
sgx-exinfo sgx-kss sgx-mode64 sgx-provisionkey sgx-tokenkey sgx1 sgx2
sgxlc sha-ni skinit skip-l1dfl-vmentry smap smep smx spec-ctrl
split-lock-detect ss ssb-no ssbd sse sse2 sse4.1 sse4.2 sse4a ssse3 stibp
svm svm-lock svme-addr-chk syscall taa-no tbm tce tm tm2 topoext tsc
tsc-adjust tsc-deadline tsc-scale tsx-ctrl tsx-ldtrk umip v-vmsave-vmload
vaes vgif virt-ssbd vmcb-clean vme vmx vmx-activity-hlt
vmx-activity-shutdown vmx-activity-wait-sipi vmx-apicv-register
vmx-apicv-vid vmx-apicv-x2apic vmx-apicv-xapic vmx-cr3-load-noexit
vmx-cr3-store-noexit vmx-cr8-load-exit vmx-cr8-store-exit vmx-desc-exit
vmx-encls-exit vmx-entry-ia32e-mode vmx-entry-load-bndcfgs
vmx-entry-load-efer vmx-entry-load-pat vmx-entry-load-perf-global-ctrl
vmx-entry-load-pkrs vmx-entry-load-rtit-ctl vmx-entry-noload-debugctl
vmx-ept vmx-ept-1gb vmx-ept-2mb vmx-ept-advanced-exitinfo
vmx-ept-execonly vmx-eptad vmx-eptp-switching vmx-exit-ack-intr
vmx-exit-clear-bndcfgs vmx-exit-clear-rtit-ctl vmx-exit-load-efer
vmx-exit-load-pat vmx-exit-load-perf-global-ctrl vmx-exit-load-pkrs
vmx-exit-nosave-debugctl vmx-exit-save-efer vmx-exit-save-pat
vmx-exit-save-preemption-timer vmx-flexpriority vmx-hlt-exit vmx-ins-outs
vmx-intr-exit vmx-invept vmx-invept-all-context vmx-invept-single-context
vmx-invept-single-context vmx-invept-single-context-noglobals
vmx-invlpg-exit vmx-invpcid-exit vmx-invvpid vmx-invvpid-all-context
vmx-invvpid-single-addr vmx-io-bitmap vmx-io-exit vmx-monitor-exit
vmx-movdr-exit vmx-msr-bitmap vmx-mtf vmx-mwait-exit vmx-nmi-exit
vmx-page-walk-4 vmx-page-walk-5 vmx-pause-exit vmx-ple vmx-pml
vmx-posted-intr vmx-preemption-timer vmx-rdpmc-exit vmx-rdrand-exit
vmx-rdseed-exit vmx-rdtsc-exit vmx-rdtscp-exit vmx-secondary-ctls
vmx-shadow-vmcs vmx-store-lma vmx-true-ctls vmx-tsc-offset
vmx-tsc-scaling vmx-unrestricted-guest vmx-vintr-pending vmx-vmfunc
vmx-vmwrite-vmexit-fields vmx-vnmi vmx-vnmi-pending vmx-vpid
vmx-wbinvd-exit vmx-xsaves vmx-zero-len-inject vpclmulqdq waitpkg
wbnoinvd wdt x2apic xcrypt xcrypt-en xfd xgetbv1 xop xsave xsavec
xsaveerptr xsaveopt xsaves xstore xstore-en xtpr
----------------------------------
CPU
----------------------------------
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Address sizes: 46 bits physical, 48 bits virtual
Byte Order: Little Endian
CPU(s): 20
On-line CPU(s) list: 0-19
Vendor ID: GenuineIntel
Model name: 12th Gen Intel(R) Core(TM) i7-12700
CPU family: 6
Model: 151
Thread(s) per core: 2
Core(s) per socket: 12
Socket(s): 1
Stepping: 2
CPU max MHz: 4900.0000
CPU min MHz: 800.0000
BogoMIPS: 4224.00
Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2
ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc art arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf tsc_known_f
req pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 sdbg fma cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer a
es xsave avx f16c rdrand lahf_lm abm 3dnowprefetch cpuid_fault epb ssbd ibrs ibpb stibp ibrs_enhanced tpr_shadow flexpriority ept vpid ept_ad fsg
sbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid rdseed adx smap clflushopt clwb intel_pt sha_ni xsaveopt xsavec xgetbv1 xsaves split_lock_detec
t user_shstk avx_vnni dtherm ida arat pln pts hwp hwp_notify hwp_act_window hwp_epp hwp_pkg_req hfi vnmi umip pku ospke waitpkg gfni vaes vpclmul
qdq tme rdpid movdiri movdir64b fsrm md_clear serialize pconfig arch_lbr ibt flush_l1d arch_capabilities
Virtualization: VT-x
L1d cache: 512 KiB (12 instances)
L1i cache: 512 KiB (12 instances)
L2 cache: 12 MiB (9 instances)
L3 cache: 25 MiB (1 instance)
NUMA node(s): 1
NUMA node0 CPU(s): 0-19
Vulnerability Gather data sampling: Not affected
Vulnerability Itlb multihit: Not affected
Vulnerability L1tf: Not affected
Vulnerability Mds: Not affected
Vulnerability Meltdown: Not affected
Vulnerability Mmio stale data: Not affected
Vulnerability Reg file data sampling: Mitigation; Clear Register File
Vulnerability Retbleed: Not affected
Vulnerability Spec rstack overflow: Not affected
Vulnerability Spec store bypass: Mitigation; Speculative Store Bypass disabled via prctl
Vulnerability Spectre v1: Mitigation; usercopy/swapgs barriers and __user pointer sanitization
Vulnerability Spectre v2: Mitigation; Enhanced / Automatic IBRS; IBPB conditional; RSB filling; PBRSB-eIBRS SW sequence; BHI BHI_DIS_
S
Vulnerability Srbds: Not affected
Vulnerability Tsx async abort: Not affected
```
</details>
There is another fix, by only keeping the drivers needed on the virtio cd.
Keeps only NetKVM vioscsi, viostor and the msi/exe files in root.
This allows normal install.
Thats what I’m using at least till a real fix is done, even though its quite hacky..
Why this works? No idea..
export VM_PATH="$HOME/windows-11"
echo "Fixing virtio iso"
mkdir -p "${VM_PATH}/virtio-cd"
7z x "${VM_PATH}/virtio-win.iso" -o"${VM_PATH}/virtio-cd" -bso0 -bsp0
[[ -d "${VM_PATH}/virtio-cd" && "$(ls -A "${VM_PATH}/virtio-cd")" ]] || { echo "Error: Extraction of virtio-cd failed!"; exit 1; }
pushd "${VM_PATH}/virtio-cd"
find . -mindepth 1 -maxdepth 1 ! -name "NetKVM" ! -name "vioscsi" ! -name "viostor" ! -name "*.msi" ! -name "*.exe" -exec rm -rf {} +
popd
rm -rf "${VM_PATH}/virtio-win.iso"
mkisofs -quiet -o "${VM_PATH}/virtio-win.iso" -V "fixed-cd" -J -R "${VM_PATH}/virtio-cd"
I ran the script and selected the fixed drive. To launch the script I used this command with the suggestions
from
opened 03:45AM - 11 Oct 24 UTC
closed 09:33PM - 17 Oct 25 UTC
bug
good first issue
**I confirm this bug has not already been reported**
- [x] I have searched the … issues and this bug has not been reported previously
**Describe the bug**

**To Reproduce**
Steps to reproduce the behavior:
1. `quickget windows 11`
2. `quickemu --vm windows-11.conf`
3. see error
**Expected behavior**
no error
**Quickemu output**
Run `quickemu` or `quickemu` and include the output of the failure below:
<details>
<summary>Quickemu output</summary>
```text
_ _
__ _ _ _(_) ___| | _____ _ __ ___ _ _
/ _' | | | | |/ __| |/ / _ \ '_ ' _ \| | | |
| (_| | |_| | | (__| < __/ | | | | | |_| |
\__, |\__,_|_|\___|_|\_\___|_| |_| |_|\__,_|
|_| v4.9.6, using qemu 7.0.0
--------------------------------------------------------------------------------
Project - https://github.com/quickemu-project/quickemu
Discord - https://wimpysworld.io/discord
--------------------------------------------------------------------------------
Usage
quickemu --vm ubuntu.conf <arguments>
Arguments
--access : Enable remote spice access support. 'local' (default), 'remote', 'clientipaddress'
--braille : Enable braille support. Requires SDL.
--delete-disk : Delete the disk image and EFI variables
--delete-vm : Delete the entire VM and its configuration
--display : Select display backend. 'sdl' (default), 'cocoa', 'gtk', 'none', 'spice' or 'spice-app'
--fullscreen : Starts VM in full screen mode (Ctl+Alt+f to exit)
--ignore-msrs-always : Configure KVM to always ignore unhandled machine-specific registers
--kill : Kill the VM process if it is running
--offline : Override all network settings and start the VM offline
--shortcut : Create a desktop shortcut
--snapshot apply <tag> : Apply/restore a snapshot.
--snapshot create <tag> : Create a snapshot.
--snapshot delete <tag> : Delete a snapshot.
--snapshot info : Show disk/snapshot info.
--status-quo : Do not commit any changes to disk/snapshot.
--viewer <viewer> : Choose an alternative viewer. @Options: 'spicy' (default), 'remote-viewer', 'none'
--width <width> : Set VM screen width; requires '--height'
--height <height> : Set VM screen height; requires '--width'
--ssh-port <port> : Set SSH port manually
--spice-port <port> : Set SPICE port manually
--public-dir <path> : Expose share directory. @Options: '' (default: xdg-user-dir PUBLICSHARE), '<directory>', 'none'
--monitor <type> : Set monitor connection type. @Options: 'socket' (default), 'telnet', 'none'
--monitor-telnet-host <ip/host> : Set telnet host for monitor. (default: 'localhost')
--monitor-telnet-port <port> : Set telnet port for monitor. (default: '4440')
--monitor-cmd <cmd> : Send command to monitor if available. (Example: system_powerdown)
--serial <type> : Set serial connection type. @Options: 'socket' (default), 'telnet', 'none'
--serial-telnet-host <ip/host> : Set telnet host for serial. (default: 'localhost')
--serial-telnet-port <port> : Set telnet port for serial. (default: '6660')
--keyboard <type> : Set keyboard. @Options: 'usb' (default), 'ps2', 'virtio'
--keyboard_layout <layout> : Set keyboard layout: 'en-us' (default)
--mouse <type> : Set mouse. @Options: 'tablet' (default), 'ps2', 'usb', 'virtio'
--usb-controller <type> : Set usb-controller. @Options: 'ehci' (default), 'xhci', 'none'
--sound-card <type> : Set sound card. @Options: 'intel-hda' (default), 'ac97', 'es1370', 'sb16', 'usb-audio', 'none'
--sound-duplex <type> : Set sound card duplex. @Options: 'hda-micro' (default: speaker/mic), 'hda-duplex' (line-in/line-out), 'hda-
output' (output-only)
--extra_args <arguments> : Pass additional arguments to qemu
--version : Print version
```
</details>
**System information**
Run `quickreport` and include the output here; if you can't run `quickreport`,
please provide the output of the following:
<details>
<summary>Quickreport output</summary>
```text
----------------------------------
Quickemu 4.9.6
----------------------------------
Distro: Ubuntu 22.04.5 LTS
Kernel: Linux 6.8.0-45-generic x86_64
Memory: 23G
GPU:
- NVIDIA Corporation GK208B [GeForce GT 730] (rev a1)
----------------------------------
curl 7.81.0
----------------------------------
Libraries: libcurl/7.81.0 OpenSSL/3.0.2 zlib/1.2.11 brotli/1.0.9 zstd/1.4.8 libidn2/2.3.2 libpsl/0.21.0 (+libidn2/2.3.2) libssh/0.9.6/openssl/zli
b nghttp2/1.43.0 librtmp/2.3 OpenLDAP/2.5.18
Protocols: dict file ftp ftps gopher gophers http https imap imaps ldap ldaps mqtt pop3 pop3s rtmp rtsp scp sftp smb smbs smtp smtps telnet tftp
Features: alt-svc AsynchDNS brotli GSS-API HSTS HTTP2 HTTPS-proxy IDN IPv6 Kerberos Largefile libz NTLM NTLM_WB PSL SPNEGO SSL TLS-SRP UnixSocke
ts zstd
----------------------------------
QEMU 7.0.0
----------------------------------
Available CPUs:
x86 486 (alias configured by machine type)
x86 486-v1
x86 Broadwell (alias configured by machine type)
x86 Broadwell-IBRS (alias of Broadwell-v3)
x86 Broadwell-noTSX (alias of Broadwell-v2)
x86 Broadwell-noTSX-IBRS (alias of Broadwell-v4)
x86 Broadwell-v1 Intel Core Processor (Broadwell)
x86 Broadwell-v2 Intel Core Processor (Broadwell, no TSX)
x86 Broadwell-v3 Intel Core Processor (Broadwell, IBRS)
x86 Broadwell-v4 Intel Core Processor (Broadwell, no TSX, IBRS)
x86 Cascadelake-Server (alias configured by machine type)
x86 Cascadelake-Server-noTSX (alias of Cascadelake-Server-v3)
x86 Cascadelake-Server-v1 Intel Xeon Processor (Cascadelake)
x86 Cascadelake-Server-v2 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES]
x86 Cascadelake-Server-v3 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v4 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, no TSX]
x86 Cascadelake-Server-v5 Intel Xeon Processor (Cascadelake) [ARCH_CAPABILITIES, EPT switching, XSAVES, no TSX]
x86 Conroe (alias configured by machine type)
x86 Conroe-v1 Intel Celeron_4x0 (Conroe/Merom Class Core 2)
x86 Cooperlake (alias configured by machine type)
x86 Cooperlake-v1 Intel Xeon Processor (Cooperlake)
x86 Cooperlake-v2 Intel Xeon Processor (Cooperlake) [XSAVES]
x86 Denverton (alias configured by machine type)
x86 Denverton-v1 Intel Atom Processor (Denverton)
x86 Denverton-v2 Intel Atom Processor (Denverton) [no MPX, no MONITOR]
x86 Denverton-v3 Intel Atom Processor (Denverton) [XSAVES, no MPX, no MONITOR]
x86 Dhyana (alias configured by machine type)
x86 Dhyana-v1 Hygon Dhyana Processor
x86 Dhyana-v2 Hygon Dhyana Processor [XSAVES]
x86 EPYC (alias configured by machine type)
x86 EPYC-IBPB (alias of EPYC-v2)
x86 EPYC-Milan (alias configured by machine type)
x86 EPYC-Milan-v1 AMD EPYC-Milan Processor
x86 EPYC-Rome (alias configured by machine type)
x86 EPYC-Rome-v1 AMD EPYC-Rome Processor
x86 EPYC-Rome-v2 AMD EPYC-Rome Processor
x86 EPYC-v1 AMD EPYC Processor
x86 EPYC-v2 AMD EPYC Processor (with IBPB)
x86 EPYC-v3 AMD EPYC Processor
x86 Haswell (alias configured by machine type)
x86 Haswell-IBRS (alias of Haswell-v3)
x86 Haswell-noTSX (alias of Haswell-v2)
x86 Haswell-noTSX-IBRS (alias of Haswell-v4)
x86 Haswell-v1 Intel Core Processor (Haswell)
x86 Haswell-v2 Intel Core Processor (Haswell, no TSX)
x86 Haswell-v3 Intel Core Processor (Haswell, IBRS)
x86 Haswell-v4 Intel Core Processor (Haswell, no TSX, IBRS)
x86 Icelake-Client (alias configured by machine type)
x86 Icelake-Client-noTSX (alias of Icelake-Client-v2)
x86 Icelake-Client-v1 Intel Core Processor (Icelake) [deprecated]
x86 Icelake-Client-v2 Intel Core Processor (Icelake) [no TSX, deprecated]
x86 Icelake-Client-v3 Intel Core Processor (Icelake) [no TSX, XSAVES, deprecated]
x86 Icelake-Server (alias configured by machine type)
x86 Icelake-Server-noTSX (alias of Icelake-Server-v2)
x86 Icelake-Server-v1 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v2 Intel Xeon Processor (Icelake) [no TSX]
x86 Icelake-Server-v3 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v4 Intel Xeon Processor (Icelake)
x86 Icelake-Server-v5 Intel Xeon Processor (Icelake) [XSAVES]
x86 Icelake-Server-v6 Intel Xeon Processor (Icelake) [5-level EPT]
x86 IvyBridge (alias configured by machine type)
x86 IvyBridge-IBRS (alias of IvyBridge-v2)
x86 IvyBridge-v1 Intel Xeon E3-12xx v2 (Ivy Bridge)
x86 IvyBridge-v2 Intel Xeon E3-12xx v2 (Ivy Bridge, IBRS)
x86 KnightsMill (alias configured by machine type)
x86 KnightsMill-v1 Intel Xeon Phi Processor (Knights Mill)
x86 Nehalem (alias configured by machine type)
x86 Nehalem-IBRS (alias of Nehalem-v2)
x86 Nehalem-v1 Intel Core i7 9xx (Nehalem Class Core i7)
x86 Nehalem-v2 Intel Core i7 9xx (Nehalem Core i7, IBRS update)
x86 Opteron_G1 (alias configured by machine type)
x86 Opteron_G1-v1 AMD Opteron 240 (Gen 1 Class Opteron)
x86 Opteron_G2 (alias configured by machine type)
x86 Opteron_G2-v1 AMD Opteron 22xx (Gen 2 Class Opteron)
x86 Opteron_G3 (alias configured by machine type)
x86 Opteron_G3-v1 AMD Opteron 23xx (Gen 3 Class Opteron)
x86 Opteron_G4 (alias configured by machine type)
x86 Opteron_G4-v1 AMD Opteron 62xx class CPU
x86 Opteron_G5 (alias configured by machine type)
x86 Opteron_G5-v1 AMD Opteron 63xx class CPU
x86 Penryn (alias configured by machine type)
x86 Penryn-v1 Intel Core 2 Duo P9xxx (Penryn Class Core 2)
x86 SandyBridge (alias configured by machine type)
x86 SandyBridge-IBRS (alias of SandyBridge-v2)
x86 SandyBridge-v1 Intel Xeon E312xx (Sandy Bridge)
x86 SandyBridge-v2 Intel Xeon E312xx (Sandy Bridge, IBRS update)
x86 Skylake-Client (alias configured by machine type)
x86 Skylake-Client-IBRS (alias of Skylake-Client-v2)
x86 Skylake-Client-noTSX-IBRS (alias of Skylake-Client-v3)
x86 Skylake-Client-v1 Intel Core Processor (Skylake)
x86 Skylake-Client-v2 Intel Core Processor (Skylake, IBRS)
x86 Skylake-Client-v3 Intel Core Processor (Skylake, IBRS, no TSX)
x86 Skylake-Client-v4 Intel Core Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, no TSX]
x86 Skylake-Server (alias configured by machine type)
x86 Skylake-Server-IBRS (alias of Skylake-Server-v2)
x86 Skylake-Server-noTSX-IBRS (alias of Skylake-Server-v3)
x86 Skylake-Server-v1 Intel Xeon Processor (Skylake)
x86 Skylake-Server-v2 Intel Xeon Processor (Skylake, IBRS)
x86 Skylake-Server-v3 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v4 Intel Xeon Processor (Skylake, IBRS, no TSX)
x86 Skylake-Server-v5 Intel Xeon Processor (Skylake, IBRS, no TSX) [IBRS, XSAVES, EPT switching, no TSX]
x86 Snowridge (alias configured by machine type)
x86 Snowridge-v1 Intel Atom Processor (SnowRidge)
x86 Snowridge-v2 Intel Atom Processor (Snowridge, no MPX)
x86 Snowridge-v3 Intel Atom Processor (Snowridge, no MPX) [XSAVES, no MPX]
x86 Snowridge-v4 Intel Atom Processor (Snowridge, no MPX) [no split lock detect, no core-capability]
x86 Westmere (alias configured by machine type)
x86 Westmere-IBRS (alias of Westmere-v2)
x86 Westmere-v1 Westmere E56xx/L56xx/X56xx (Nehalem-C)
x86 Westmere-v2 Westmere E56xx/L56xx/X56xx (IBRS update)
x86 athlon (alias configured by machine type)
x86 athlon-v1 QEMU Virtual CPU version 2.5+
x86 core2duo (alias configured by machine type)
x86 core2duo-v1 Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz
x86 coreduo (alias configured by machine type)
x86 coreduo-v1 Genuine Intel(R) CPU T2600 @ 2.16GHz
x86 kvm32 (alias configured by machine type)
x86 kvm32-v1 Common 32-bit KVM processor
x86 kvm64 (alias configured by machine type)
x86 kvm64-v1 Common KVM processor
x86 n270 (alias configured by machine type)
x86 n270-v1 Intel(R) Atom(TM) CPU N270 @ 1.60GHz
x86 pentium (alias configured by machine type)
x86 pentium-v1
x86 pentium2 (alias configured by machine type)
x86 pentium2-v1
x86 pentium3 (alias configured by machine type)
x86 pentium3-v1
x86 phenom (alias configured by machine type)
x86 phenom-v1 AMD Phenom(tm) 9550 Quad-Core Processor
x86 qemu32 (alias configured by machine type)
x86 qemu32-v1 QEMU Virtual CPU version 2.5+
x86 qemu64 (alias configured by machine type)
x86 qemu64-v1 QEMU Virtual CPU version 2.5+
x86 base base CPU model type with no features enabled
x86 host processor with all supported host features
x86 max Enables all features supported by the accelerator in the current host
Recognized CPUID flags:
3dnow 3dnowext 3dnowprefetch abm ace2 ace2-en acpi adx aes amd-no-ssb
amd-ssbd amd-stibp amx-bf16 amx-int8 amx-tile apic arat arch-capabilities
avic avx avx-vnni avx2 avx512-4fmaps avx512-4vnniw avx512-bf16
avx512-fp16 avx512-vp2intersect avx512-vpopcntdq avx512bitalg avx512bw
avx512cd avx512dq avx512er avx512f avx512ifma avx512pf avx512vbmi
avx512vbmi2 avx512vl avx512vnni bmi1 bmi2 bus-lock-detect cid cldemote
clflush clflushopt clwb clzero cmov cmp-legacy core-capability cr8legacy
cx16 cx8 dca de decodeassists ds ds-cpl dtes64 erms est extapic f16c
flushbyasid fma fma4 fpu fsgsbase fsrm full-width-write fxsr fxsr-opt
gfni hle ht hypervisor ia64 ibpb ibrs ibrs-all ibs intel-pt intel-pt-lip
invpcid invtsc kvm-asyncpf kvm-asyncpf-int kvm-hint-dedicated kvm-mmu
kvm-msi-ext-dest-id kvm-nopiodelay kvm-poll-control kvm-pv-eoi kvm-pv-ipi
kvm-pv-sched-yield kvm-pv-tlb-flush kvm-pv-unhalt kvm-steal-time kvmclock
kvmclock kvmclock-stable-bit la57 lahf-lm lbrv lm lwp mca mce md-clear
mds-no misalignsse mmx mmxext monitor movbe movdir64b movdiri mpx msr
mtrr nodeid-msr npt nrip-save nx osvw pae pat pause-filter pbe pcid
pclmulqdq pcommit pdcm pdpe1gb perfctr-core perfctr-nb pfthreshold pge
phe phe-en pks pku pmm pmm-en pn pni popcnt pschange-mc-no pse pse36
rdctl-no rdpid rdrand rdseed rdtscp rsba rtm sep serialize sgx sgx-debug
sgx-exinfo sgx-kss sgx-mode64 sgx-provisionkey sgx-tokenkey sgx1 sgx2
sgxlc sha-ni skinit skip-l1dfl-vmentry smap smep smx spec-ctrl
split-lock-detect ss ssb-no ssbd sse sse2 sse4.1 sse4.2 sse4a ssse3 stibp
svm svm-lock svme-addr-chk syscall taa-no tbm tce tm tm2 topoext tsc
tsc-adjust tsc-deadline tsc-scale tsx-ctrl tsx-ldtrk umip v-vmsave-vmload
vaes vgif virt-ssbd vmcb-clean vme vmx vmx-activity-hlt
vmx-activity-shutdown vmx-activity-wait-sipi vmx-apicv-register
vmx-apicv-vid vmx-apicv-x2apic vmx-apicv-xapic vmx-cr3-load-noexit
vmx-cr3-store-noexit vmx-cr8-load-exit vmx-cr8-store-exit vmx-desc-exit
vmx-encls-exit vmx-entry-ia32e-mode vmx-entry-load-bndcfgs
vmx-entry-load-efer vmx-entry-load-pat vmx-entry-load-perf-global-ctrl
vmx-entry-load-pkrs vmx-entry-load-rtit-ctl vmx-entry-noload-debugctl
vmx-ept vmx-ept-1gb vmx-ept-2mb vmx-ept-advanced-exitinfo
vmx-ept-execonly vmx-eptad vmx-eptp-switching vmx-exit-ack-intr
vmx-exit-clear-bndcfgs vmx-exit-clear-rtit-ctl vmx-exit-load-efer
vmx-exit-load-pat vmx-exit-load-perf-global-ctrl vmx-exit-load-pkrs
vmx-exit-nosave-debugctl vmx-exit-save-efer vmx-exit-save-pat
vmx-exit-save-preemption-timer vmx-flexpriority vmx-hlt-exit vmx-ins-outs
vmx-intr-exit vmx-invept vmx-invept-all-context vmx-invept-single-context
vmx-invept-single-context vmx-invept-single-context-noglobals
vmx-invlpg-exit vmx-invpcid-exit vmx-invvpid vmx-invvpid-all-context
vmx-invvpid-single-addr vmx-io-bitmap vmx-io-exit vmx-monitor-exit
vmx-movdr-exit vmx-msr-bitmap vmx-mtf vmx-mwait-exit vmx-nmi-exit
vmx-page-walk-4 vmx-page-walk-5 vmx-pause-exit vmx-ple vmx-pml
vmx-posted-intr vmx-preemption-timer vmx-rdpmc-exit vmx-rdrand-exit
vmx-rdseed-exit vmx-rdtsc-exit vmx-rdtscp-exit vmx-secondary-ctls
vmx-shadow-vmcs vmx-store-lma vmx-true-ctls vmx-tsc-offset
vmx-tsc-scaling vmx-unrestricted-guest vmx-vintr-pending vmx-vmfunc
vmx-vmwrite-vmexit-fields vmx-vnmi vmx-vnmi-pending vmx-vpid
vmx-wbinvd-exit vmx-xsaves vmx-zero-len-inject vpclmulqdq waitpkg
wbnoinvd wdt x2apic xcrypt xcrypt-en xfd xgetbv1 xop xsave xsavec
xsaveerptr xsaveopt xsaves xstore xstore-en xtpr
----------------------------------
CPU
----------------------------------
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Address sizes: 46 bits physical, 48 bits virtual
Byte Order: Little Endian
CPU(s): 20
On-line CPU(s) list: 0-19
Vendor ID: GenuineIntel
Model name: 12th Gen Intel(R) Core(TM) i7-12700
CPU family: 6
Model: 151
Thread(s) per core: 2
Core(s) per socket: 12
Socket(s): 1
Stepping: 2
CPU max MHz: 4900.0000
CPU min MHz: 800.0000
BogoMIPS: 4224.00
Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2
ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc art arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf tsc_known_f
req pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 sdbg fma cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer a
es xsave avx f16c rdrand lahf_lm abm 3dnowprefetch cpuid_fault epb ssbd ibrs ibpb stibp ibrs_enhanced tpr_shadow flexpriority ept vpid ept_ad fsg
sbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid rdseed adx smap clflushopt clwb intel_pt sha_ni xsaveopt xsavec xgetbv1 xsaves split_lock_detec
t user_shstk avx_vnni dtherm ida arat pln pts hwp hwp_notify hwp_act_window hwp_epp hwp_pkg_req hfi vnmi umip pku ospke waitpkg gfni vaes vpclmul
qdq tme rdpid movdiri movdir64b fsrm md_clear serialize pconfig arch_lbr ibt flush_l1d arch_capabilities
Virtualization: VT-x
L1d cache: 512 KiB (12 instances)
L1i cache: 512 KiB (12 instances)
L2 cache: 12 MiB (9 instances)
L3 cache: 25 MiB (1 instance)
NUMA node(s): 1
NUMA node0 CPU(s): 0-19
Vulnerability Gather data sampling: Not affected
Vulnerability Itlb multihit: Not affected
Vulnerability L1tf: Not affected
Vulnerability Mds: Not affected
Vulnerability Meltdown: Not affected
Vulnerability Mmio stale data: Not affected
Vulnerability Reg file data sampling: Mitigation; Clear Register File
Vulnerability Retbleed: Not affected
Vulnerability Spec rstack overflow: Not affected
Vulnerability Spec store bypass: Mitigation; Speculative Store Bypass disabled via prctl
Vulnerability Spectre v1: Mitigation; usercopy/swapgs barriers and __user pointer sanitization
Vulnerability Spectre v2: Mitigation; Enhanced / Automatic IBRS; IBPB conditional; RSB filling; PBRSB-eIBRS SW sequence; BHI BHI_DIS_
S
Vulnerability Srbds: Not affected
Vulnerability Tsx async abort: Not affected
```
</details>
commenting out fixed iso and adding:
--extra_args "--drive media=cdrom,index=3,file=windows-11/virtio-win.iso"
Seems to get me to be able to load drivers from it, without just a black screen after some selections otherwise.
quickemu --vm windows-11.conf --extra_args "--drive media=cdrom,index=3,file=windows-11/virtio-win.iso" -display spice
When selecting the driver, I picked the NetKVM drivers from the cd from the am64 folder. After applying these patches, I was able to boot into windows. When I tried passing my xbox controller with spice, Windows detected it initially then stopped working. Pairing with the bluetooth dongle worked, but I couldn’t update the controller firmware.