@Exard3k i have regural ram i have 2 slots only. my card is pci-e 3.0 x8
1. also 5600x works fine but it has no gpu
3. card is pci-e 3.0 x8 and it has pci-e switch on card that switches between
2x nvme and nic
iommu setting by default is disabled it tried to enable and no change. also i did add gpu memory and set display form pci-e to igpu no change there.
motherboard does not detect pci-e x4 nic either
i run that platform on unraid so its linux basicly.
Does that particular board disable slots for APUs? Check with vendor. Especially if everything is working with a 5600x
@Exard3k manual does not say anything about that particlular cpu or any apu support told me to reset cmos. i mean when i upgrade bios it already resets everything and after bios upgrade i did also reset bios to make sure.
Iām not talking about CMOS settings. Most boards donāt have the same slot layout for APUs. My board has a x16 and a x8 slot. If I plug in an APU, I only have the x16 because the x8 is disabled for APUs. It just doesnāt exist anymore for my board despite physically visible and touchable.
Donāt know what the hell a 200ge isā¦but board vendor should have infos on that. My certainly does (AsRock)
@Exard3k offical website does not tell anything but
from guru 3d:
just hooked up old 7900gtx and it works so x16 works but not x8 and x4
[10de:0290] 01:00.0 VGA compatible controller: NVIDIA Corporation G71 [GeForce 7900 GTX] (rev a1)
So, summarizing the situation:
Would it be possible to run Linux on a USB key and post the output of the following two commands, on both CPUs? Also, make sure no pins are bent on the 5600G or something stupid like that.
lspci -vt
lspci -vv
I am also pretty sure the Synology card (I really like that btw, thatās forward thinking for sure 
) needs bifurcation in some form to work properly. Before you do anything else though, reinstall Windows, it is possible the 200GE and 5600G are different enough you just need to reset the hardware configuration.
Iām thinking probably needs 4/4/4/4 split rather than 8/anything
@mfdoom7 Did you already open a ticket with Gigabyte ? Because this feels more and more of a bug in the bios somewhere. With this situation. A install could work. but that wouldnāt explain why its working on the other processors.
@wertigon i run hardware on unraid so its basicly linux. no cpu pins are bent its already replaced cpu i rma-d it but all same. motherboard bios do not have bifurcation setting and intel system also works with that card and no bifurcation needed 9900k with z390 aorus master.
i will run those commands and copy here ?
@Mongoosh yes i talked to support and they told me to reset cmos and after that replace cpu and i did that and same problem with new cpu.
@Mongoosh
dmesg
[ 0.000000] Linux version 5.10.28-Unraid (root@Develop) (gcc (GCC) 9.3.0, GNU ld version 2.33.1-slack15) #1 SMP Wed Apr 7 08:23:18 PDT 2021
[ 0.000000] Command line: BOOT_IMAGE=/bzimage initrd=/bzroot
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: āx87 floating point registersā
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: āSSE registersā
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: āAVX registersā
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x200: āProtection Keys User registersā
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: xstate_offset[9]: 832, xstate_sizes[9]: 8
[ 0.000000] x86/fpu: Enabled xstate features 0x207, context size is 840 bytes, using ācompactedā format.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d3ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d400-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000009c1efff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000009c1f000-0x0000000009ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000a000000-0x000000000a1fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000a200000-0x000000000a20cfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000a20d000-0x000000000affffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000b000000-0x000000000b01ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000b020000-0x00000000b9e98fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000b9e99000-0x00000000ba1cefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ba1cf000-0x00000000ba210fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000ba211000-0x00000000bbc8efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bbc8f000-0x00000000bcbfefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bcbff000-0x00000000bdffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000be000000-0x00000000bfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd200000-0x00000000fd2fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fd600000-0x00000000fd6fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000fea0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb80000-0x00000000fec01fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec30000-0x00000000fec30fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedc2000-0x00000000fedcffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fedd4000-0x00000000fedd5fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021e2fffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000021e300000-0x000000023fffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 3.3.0 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. B450 I AORUS PRO WIFI/B450 I AORUS PRO WIFI-CF, BIOS F61 07/13/2021
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3892.613 MHz processor
[ 0.000359] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000360] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000365] last_pfn = 0x21e300 max_arch_pfn = 0x400000000
[ 0.000368] MTRR default type: uncachable
[ 0.000368] MTRR fixed ranges enabled:
[ 0.000369] 00000-9FFFF write-back
[ 0.000369] A0000-BFFFF write-through
[ 0.000370] C0000-FFFFF write-protect
[ 0.000370] MTRR variable ranges enabled:
[ 0.000371] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000372] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000372] 2 disabled
[ 0.000372] 3 disabled
[ 0.000372] 4 disabled
[ 0.000373] 5 disabled
[ 0.000373] 6 disabled
[ 0.000373] 7 disabled
[ 0.000374] TOM2: 0000000240000000 aka 9216M
[ 0.000664] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000852] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
[ 0.000856] last_pfn = 0xbe000 max_arch_pfn = 0x400000000
[ 0.003430] ACPI: Early table checksum verification disabled
[ 0.003432] ACPI: RSDP 0x00000000000F05B0 000024 (v02 ALASKA)
[ 0.003434] ACPI: XSDT 0x00000000BBC77728 0000CC (v01 ALASKA A M I 01072009 AMI 01000013)
[ 0.003438] ACPI: FACP 0x00000000BA1FC000 000114 (v06 ALASKA A M I 01072009 AMI 00010013)
[ 0.003441] ACPI: DSDT 0x00000000BA1F5000 006034 (v02 ALASKA A M I 01072009 INTL 20190509)
[ 0.003443] ACPI: FACS 0x00000000BAC72000 000040
[ 0.003445] ACPI: SSDT 0x00000000BA20B000 005D89 (v02 GBT GSWApp 00000001 INTL 20190509)
[ 0.003446] ACPI: IVRS 0x00000000BA20A000 0000D0 (v02 AMD AmdTable 00000001 AMD 00000001)
[ 0.003448] ACPI: SSDT 0x00000000BA202000 00723C (v02 AMD MYRTLE 00000002 MSFT 04000000)
[ 0.003449] ACPI: SSDT 0x00000000BA1FE000 003D06 (v01 AMD AMD AOD 00000001 INTL 20190509)
[ 0.003451] ACPI: SSDT 0x00000000BA1FD000 0000C8 (v02 ALASKA CPUSSDT 01072009 AMI 01072009)
[ 0.003452] ACPI: FIDT 0x00000000BA1F4000 00009C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.003454] ACPI: MCFG 0x00000000BA1F3000 00003C (v01 ALASKA A M I 01072009 MSFT 00010013)
[ 0.003455] ACPI: HPET 0x00000000BA1F2000 000038 (v01 ALASKA A M I 01072009 AMI 00000005)
[ 0.003457] ACPI: SSDT 0x00000000BA1ED000 003E4C (v02 AMD AmdTable 00000001 AMD 00000001)
[ 0.003458] ACPI: CRAT 0x00000000BA1EC000 000B68 (v01 AMD AmdTable 00000001 AMD 00000001)
[ 0.003459] ACPI: CDIT 0x00000000BA1EB000 000029 (v01 AMD AmdTable 00000001 AMD 00000001)
[ 0.003461] ACPI: SSDT 0x00000000BA1E9000 001486 (v01 AMD MYRTLEG2 00000001 INTL 20190509)
[ 0.003462] ACPI: SSDT 0x00000000BA1E7000 0014FD (v01 AMD MYRTLEPX 00000001 INTL 20190509)
[ 0.003464] ACPI: SSDT 0x00000000BA1E3000 003A59 (v01 AMD MYRTLE 00000001 INTL 20190509)
[ 0.003465] ACPI: SSDT 0x00000000BA1E2000 0000BF (v01 AMD AmdTable 00001000 INTL 20190509)
[ 0.003467] ACPI: APIC 0x00000000BA1E0000 00015E (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.003468] ACPI: SSDT 0x00000000BA1DF000 00091B (v01 AMD MYRTLERN 00000001 INTL 20190509)
[ 0.003470] ACPI: SSDT 0x00000000BA1DD000 00147F (v01 AMD MYRTLE 00000001 INTL 20190509)
[ 0.003471] ACPI: FPDT 0x00000000BA1DC000 000044 (v01 ALASKA A M I 01072009 AMI 01000013)
[ 0.003472] ACPI: WSMT 0x00000000BA1E1000 000028 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.003474] ACPI: Reserving FACP table memory at [mem 0xba1fc000-0xba1fc113]
[ 0.003474] ACPI: Reserving DSDT table memory at [mem 0xba1f5000-0xba1fb033]
[ 0.003475] ACPI: Reserving FACS table memory at [mem 0xbac72000-0xbac7203f]
[ 0.003475] ACPI: Reserving SSDT table memory at [mem 0xba20b000-0xba210d88]
[ 0.003476] ACPI: Reserving IVRS table memory at [mem 0xba20a000-0xba20a0cf]
[ 0.003476] ACPI: Reserving SSDT table memory at [mem 0xba202000-0xba20923b]
[ 0.003477] ACPI: Reserving SSDT table memory at [mem 0xba1fe000-0xba201d05]
[ 0.003477] ACPI: Reserving SSDT table memory at [mem 0xba1fd000-0xba1fd0c7]
[ 0.003478] ACPI: Reserving FIDT table memory at [mem 0xba1f4000-0xba1f409b]
[ 0.003478] ACPI: Reserving MCFG table memory at [mem 0xba1f3000-0xba1f303b]
[ 0.003479] ACPI: Reserving HPET table memory at [mem 0xba1f2000-0xba1f2037]
[ 0.003479] ACPI: Reserving SSDT table memory at [mem 0xba1ed000-0xba1f0e4b]
[ 0.003480] ACPI: Reserving CRAT table memory at [mem 0xba1ec000-0xba1ecb67]
[ 0.003480] ACPI: Reserving CDIT table memory at [mem 0xba1eb000-0xba1eb028]
[ 0.003480] ACPI: Reserving SSDT table memory at [mem 0xba1e9000-0xba1ea485]
[ 0.003481] ACPI: Reserving SSDT table memory at [mem 0xba1e7000-0xba1e84fc]
[ 0.003481] ACPI: Reserving SSDT table memory at [mem 0xba1e3000-0xba1e6a58]
[ 0.003482] ACPI: Reserving SSDT table memory at [mem 0xba1e2000-0xba1e20be]
[ 0.003482] ACPI: Reserving APIC table memory at [mem 0xba1e0000-0xba1e015d]
[ 0.003483] ACPI: Reserving SSDT table memory at [mem 0xba1df000-0xba1df91a]
[ 0.003483] ACPI: Reserving SSDT table memory at [mem 0xba1dd000-0xba1de47e]
[ 0.003484] ACPI: Reserving FPDT table memory at [mem 0xba1dc000-0xba1dc043]
[ 0.003484] ACPI: Reserving WSMT table memory at [mem 0xba1e1000-0xba1e1027]
[ 0.003489] Using GB pages for direct mapping
[ 0.004050] RAMDISK: [mem 0x772e8000-0x7fffffff]
[ 0.004062] ACPI: Local APIC address 0xfee00000
[ 0.004144] No NUMA configuration found
[ 0.004144] Faking a node at [mem 0x0000000000000000-0x000000021e2fffff]
[ 0.004147] NODE_DATA(0) allocated [mem 0x21e2fc000-0x21e2fffff]
[ 0.004161] Zone ranges:
[ 0.004162] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.004163] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.004164] Normal [mem 0x0000000100000000-0x000000021e2fffff]
[ 0.004164] Movable zone start for each node
[ 0.004165] Early memory node ranges
[ 0.004165] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.004166] node 0: [mem 0x0000000000100000-0x0000000009c1efff]
[ 0.004166] node 0: [mem 0x000000000a000000-0x000000000a1fffff]
[ 0.004167] node 0: [mem 0x000000000a20d000-0x000000000affffff]
[ 0.004167] node 0: [mem 0x000000000b020000-0x00000000b9e98fff]
[ 0.004168] node 0: [mem 0x00000000bcbff000-0x00000000bdffffff]
[ 0.004168] node 0: [mem 0x0000000100000000-0x000000021e2fffff]
[ 0.004169] Initmem setup node 0 [mem 0x0000000000001000-0x000000021e2fffff]
[ 0.004170] On node 0 totalpages: 1937704
[ 0.004171] DMA zone: 64 pages used for memmap
[ 0.004171] DMA zone: 21 pages reserved
[ 0.004172] DMA zone: 3996 pages, LIFO batch:0
[ 0.004315] DMA zone: 28772 pages in unavailable ranges
[ 0.004315] DMA32 zone: 11899 pages used for memmap
[ 0.004316] DMA32 zone: 761484 pages, LIFO batch:63
[ 0.009322] DMA32 zone: 20852 pages in unavailable ranges
[ 0.009325] Normal zone: 18316 pages used for memmap
[ 0.009326] Normal zone: 1172224 pages, LIFO batch:63
[ 0.017791] Normal zone: 7424 pages in unavailable ranges
[ 0.018250] ACPI: PM-Timer IO Port: 0x808
[ 0.018251] ACPI: Local APIC address 0xfee00000
[ 0.018256] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.018268] IOAPIC[0]: apic_id 13, version 33, address 0xfec00000, GSI 0-23
[ 0.018272] IOAPIC[1]: apic_id 14, version 33, address 0xfec01000, GSI 24-55
[ 0.018274] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.018275] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.018276] ACPI: IRQ0 used by override.
[ 0.018276] ACPI: IRQ9 used by override.
[ 0.018277] Using ACPI (MADT) for SMP configuration information
[ 0.018278] ACPI: HPET id: 0x10228201 base: 0xfed00000
[ 0.018282] smpboot: Allowing 32 CPUs, 20 hotplug CPUs
[ 0.018301] [mem 0xc0000000-0xefffffff] available for PCI devices
[ 0.018302] Booting paravirtualized kernel on bare hardware
[ 0.018304] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.020847] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:32 nr_node_ids:1
[ 0.021820] percpu: Embedded 45 pages/cpu s145240 r8192 d30888 u262144
[ 0.021825] pcpu-alloc: s145240 r8192 d30888 u262144 alloc=1*2097152
[ 0.021826] pcpu-alloc: [0] 00 01 02 03 04 05 06 07 [0] 08 09 10 11 12 13 14 15
[ 0.021830] pcpu-alloc: [0] 16 17 18 19 20 21 22 23 [0] 24 25 26 27 28 29 30 31
[ 0.021851] Built 1 zonelists, mobility grouping on. Total pages: 1907404
[ 0.021852] Policy zone: Normal
[ 0.021853] Kernel command line: BOOT_IMAGE=/bzimage initrd=/bzroot
[ 0.021888] printk: log_buf_len individual max cpu contribution: 4096 bytes
[ 0.021889] printk: log_buf_len total cpu_extra contributions: 126976 bytes
[ 0.021889] printk: log_buf_len min size: 131072 bytes
[ 0.022061] printk: log_buf_len: 262144 bytes
[ 0.022062] printk: early log buf free: 119464(91%)
[ 0.022481] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.022692] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.022748] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.044794] Memory: 7375336K/7750816K available (10242K kernel code, 1183K rwdata, 2348K rodata, 1120K init, 1596K bss, 375224K reserved, 0K cma-reserved)
[ 0.044852] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=32, Nodes=1
[ 0.044950] rcu: Hierarchical RCU implementation.
[ 0.044951] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=32.
[ 0.044952] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[ 0.044953] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=32
[ 0.044970] NR_IRQS: 16640, nr_irqs: 1224, preallocated irqs: 16
[ 0.045151] rcu: Offload RCU callbacks from CPUs: (none).
[ 0.045260] random: get_random_bytes called from start_kernel+0x31a/0x4e3 with crng_init=0
[ 0.049694] Console: colour VGA+ 80x25
[ 0.068212] printk: console [tty0] enabled
[ 0.068291] ACPI: Core revision 20200925
[ 0.068490] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.068610] APIC: Switch to symmetric I/O mode setup
[ 0.069730] Switched APIC routing to physical flat.
[ 0.070302] ā¦TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.074615] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x703831938b4, max_idle_ns: 881591041966 ns
[ 0.074736] Calibrating delay loop (skipped), value calculated using timer frequencyā¦ 7785.22 BogoMIPS (lpj=3892613)
[ 0.074854] pid_max: default: 32768 minimum: 301
[ 0.074953] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.075051] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.075315] x86/cpu: User Mode Instruction Prevention (UMIP) activated
[ 0.075419] LVT offset 1 assigned for vector 0xf9
[ 0.075542] LVT offset 2 assigned for vector 0xf4
[ 0.075752] Last level iTLB entries: 4KB 512, 2MB 512, 4MB 256
[ 0.075826] Last level dTLB entries: 4KB 2048, 2MB 2048, 4MB 1024, 1GB 0
[ 0.075909] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[ 0.076012] Spectre V2 : Mitigation: Full AMD retpoline
[ 0.076082] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[ 0.076173] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 0.076256] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[ 0.076348] Spectre V2 : User space: Mitigation: STIBP always-on protection
[ 0.076431] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[ 0.076658] Freeing SMP alternatives memory: 16K
[ 0.180516] smpboot: CPU0: AMD Ryzen 5 5600G with Radeon Graphics (family: 0x19, model: 0x50, stepping: 0x0)
[ 0.180707] Performance Events: Fam17h+ core perfctr, AMD PMU driver.
[ 0.180732] ā¦ version: 0
[ 0.180732] ā¦ bit width: 48
[ 0.180732] ā¦ generic registers: 6
[ 0.180732] ā¦ value mask: 0000ffffffffffff
[ 0.180732] ā¦ max period: 00007fffffffffff
[ 0.180732] ā¦ fixed-purpose events: 0
[ 0.180732] ā¦ event mask: 000000000000003f
[ 0.180732] rcu: Hierarchical SRCU implementation.
[ 0.180872] smp: Bringing up secondary CPUs ā¦
[ 0.181003] x86: Booting SMP configuration:
[ 0.181078] ā¦ node #0, CPUs: #1 #2 #3 #4 #5 #6
[ 0.188766] Spectre V2 : Update user space SMT mitigation: STIBP always-on
[ 0.188987] #7 #8 #9 #10 #11
[ 0.194762] smp: Brought up 1 node, 12 CPUs
[ 0.194912] smpboot: Max logical packages: 3
[ 0.194987] smpboot: Total of 12 processors activated (93422.71 BogoMIPS)
[ 0.195877] devtmpfs: initialized
[ 0.195877] x86/mm: Memory block size: 128MB
[ 0.197012] PM: Registering ACPI NVS region [mem 0x0a200000-0x0a20cfff] (53248 bytes)
[ 0.197012] PM: Registering ACPI NVS region [mem 0xba211000-0xbbc8efff] (27779072 bytes)
[ 0.197242] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.197380] futex hash table entries: 8192 (order: 7, 524288 bytes, linear)
[ 0.197782] pinctrl core: initialized pinctrl subsystem
[ 0.197944] NET: Registered protocol family 16
[ 0.198106] thermal_sys: Registered thermal governor āfair_shareā
[ 0.198106] thermal_sys: Registered thermal governor ābang_bangā
[ 0.198198] thermal_sys: Registered thermal governor āstep_wiseā
[ 0.198287] thermal_sys: Registered thermal governor āuser_spaceā
[ 0.198386] cpuidle: using governor ladder
[ 0.198386] cpuidle: using governor menu
[ 0.198759] ACPI: bus type PCI registered
[ 0.198883] PCI: MMCONFIG for domain 0000 [bus 00-7f] at [mem 0xf0000000-0xf7ffffff] (base 0xf0000000)
[ 0.199013] PCI: MMCONFIG at [mem 0xf0000000-0xf7ffffff] reserved in E820
[ 0.199118] PCI: Using configuration type 1 for base access
[ 0.200045] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.200045] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.217030] raid6: avx2x4 gen() 40371 MB/s
[ 0.234030] raid6: avx2x4 xor() 5498 MB/s
[ 0.251030] raid6: avx2x2 gen() 40996 MB/s
[ 0.268030] raid6: avx2x2 xor() 36347 MB/s
[ 0.285030] raid6: avx2x1 gen() 31306 MB/s
[ 0.302030] raid6: avx2x1 xor() 28301 MB/s
[ 0.319030] raid6: sse2x4 gen() 24657 MB/s
[ 0.336030] raid6: sse2x4 xor() 3409 MB/s
[ 0.353031] raid6: sse2x2 gen() 23162 MB/s
[ 0.370030] raid6: sse2x2 xor() 19187 MB/s
[ 0.387042] raid6: sse2x1 gen() 1319 MB/s
[ 0.404030] raid6: sse2x1 xor() 13317 MB/s
[ 0.404109] raid6: using algorithm avx2x2 gen() 40996 MB/s
[ 0.404194] raid6: ā¦ xor() 36347 MB/s, rmw enabled
[ 0.404275] raid6: using avx2x2 recovery algorithm
[ 0.404732] ACPI: Added OSI(Module Device)
[ 0.404732] ACPI: Added OSI(Processor Device)
[ 0.404732] ACPI: Added OSI(3.0 SCP Extensions)
[ 0.404732] ACPI: Added OSI(Processor Aggregator Device)
[ 0.404732] ACPI: Added OSI(Linux-Dell-Video)
[ 0.404734] ACPI: Added OSI(Linux-Lenovo-NV-HDMI-Audio)
[ 0.404817] ACPI: Added OSI(Linux-HPI-Hybrid-Graphics)
[ 0.410694] ACPI: 12 ACPI AML tables successfully acquired and loaded
[ 0.411502] ACPI: [Firmware Bug]: BIOS OSI(Linux) query ignored
[ 0.415753] ACPI: Interpreter enabled
[ 0.415835] ACPI: (supports S0 S3 S5)
[ 0.415906] ACPI: Using IOAPIC for interrupt routing
[ 0.416162] PCI: Using host bridge windows from ACPI; if necessary, use āpci=nocrsā and report a bug
[ 0.416470] ACPI: Enabled 4 GPEs in block 00 to 1F
[ 0.421741] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.421741] acpi PNP0A08:00: OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[ 0.421741] acpi PNP0A08:00: OSC: platform does not support [LTR]
[ 0.421741] acpi PNP0A08:00: OSC: OS now controls [PME AER PCIeCapability]
[ 0.421842] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-7f] only partially covers this bridge
[ 0.422064] PCI host bridge to bus 0000:00
[ 0.422140] pci_bus 0000:00: root bus resource [io 0x0000-0x03af window]
[ 0.422236] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7 window]
[ 0.422332] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df window]
[ 0.422429] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.422525] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.422627] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 0.422729] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfec2ffff window]
[ 0.422733] pci_bus 0000:00: root bus resource [mem 0xfee00000-0xffffffff window]
[ 0.422836] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.422931] pci 0000:00:00.0: [1022:1630] type 00 class 0x060000
[ 0.423737] pci 0000:00:00.2: [1022:1631] type 00 class 0x080600
[ 0.423743] pci 0000:00:01.0: [1022:1632] type 00 class 0x060000
[ 0.423744] pci 0000:00:02.0: [1022:1632] type 00 class 0x060000
[ 0.423744] pci 0000:00:02.1: [1022:1634] type 01 class 0x060400
[ 0.423744] pci 0000:00:02.1: enabling Extended Tags
[ 0.423762] pci 0000:00:02.1: PME# supported from D0 D3hot D3cold
[ 0.423907] pci 0000:00:02.2: [1022:1634] type 01 class 0x060400
[ 0.424041] pci 0000:00:02.2: PME# supported from D0 D3hot D3cold
[ 0.424743] pci 0000:00:08.0: [1022:1632] type 00 class 0x060000
[ 0.424743] pci 0000:00:08.1: [1022:1635] type 01 class 0x060400
[ 0.424743] pci 0000:00:08.1: enabling Extended Tags
[ 0.424743] pci 0000:00:08.1: PME# supported from D0 D3hot D3cold
[ 0.424743] pci 0000:00:08.2: [1022:1635] type 01 class 0x060400
[ 0.424836] pci 0000:00:08.2: enabling Extended Tags
[ 0.424936] pci 0000:00:08.2: PME# supported from D0 D3hot D3cold
[ 0.425738] pci 0000:00:14.0: [1022:790b] type 00 class 0x0c0500
[ 0.425743] pci 0000:00:14.3: [1022:790e] type 00 class 0x060100
[ 0.425743] pci 0000:00:18.0: [1022:166a] type 00 class 0x060000
[ 0.425744] pci 0000:00:18.1: [1022:166b] type 00 class 0x060000
[ 0.425744] pci 0000:00:18.2: [1022:166c] type 00 class 0x060000
[ 0.425761] pci 0000:00:18.3: [1022:166d] type 00 class 0x060000
[ 0.425869] pci 0000:00:18.4: [1022:166e] type 00 class 0x060000
[ 0.425979] pci 0000:00:18.5: [1022:166f] type 00 class 0x060000
[ 0.426088] pci 0000:00:18.6: [1022:1670] type 00 class 0x060000
[ 0.426737] pci 0000:00:18.7: [1022:1671] type 00 class 0x060000
[ 0.426743] pci 0000:01:00.0: [1022:43d5] type 00 class 0x0c0330
[ 0.426743] pci 0000:01:00.0: reg 0x10: [mem 0xfcda0000-0xfcda7fff 64bit]
[ 0.426743] pci 0000:01:00.0: enabling Extended Tags
[ 0.426743] pci 0000:01:00.0: PME# supported from D3hot D3cold
[ 0.426804] pci 0000:01:00.1: [1022:43c8] type 00 class 0x010601
[ 0.426922] pci 0000:01:00.1: reg 0x24: [mem 0xfcd80000-0xfcd9ffff]
[ 0.427009] pci 0000:01:00.1: reg 0x30: [mem 0xfcd00000-0xfcd7ffff pref]
[ 0.427098] pci 0000:01:00.1: enabling Extended Tags
[ 0.427203] pci 0000:01:00.1: PME# supported from D3hot D3cold
[ 0.427737] pci 0000:01:00.2: [1022:43c6] type 01 class 0x060400
[ 0.427737] pci 0000:01:00.2: enabling Extended Tags
[ 0.427737] pci 0000:01:00.2: PME# supported from D3hot D3cold
[ 0.427743] pci 0000:00:02.1: PCI bridge to [bus 01-08]
[ 0.427743] pci 0000:00:02.1: bridge window [io 0xf000-0xffff]
[ 0.427815] pci 0000:00:02.1: bridge window [mem 0xfcb00000-0xfcdfffff]
[ 0.427938] pci 0000:02:00.0: [1022:43c7] type 01 class 0x060400
[ 0.428054] pci 0000:02:00.0: enabling Extended Tags
[ 0.428172] pci 0000:02:00.0: PME# supported from D3hot D3cold
[ 0.428738] pci 0000:02:01.0: [1022:43c7] type 01 class 0x060400
[ 0.428738] pci 0000:02:01.0: enabling Extended Tags
[ 0.428738] pci 0000:02:01.0: PME# supported from D3hot D3cold
[ 0.428743] pci 0000:02:04.0: [1022:43c7] type 01 class 0x060400
[ 0.428854] pci 0000:02:04.0: enabling Extended Tags
[ 0.428970] pci 0000:02:04.0: PME# supported from D3hot D3cold
[ 0.429738] pci 0000:02:05.0: [1022:43c7] type 01 class 0x060400
[ 0.429738] pci 0000:02:05.0: enabling Extended Tags
[ 0.429738] pci 0000:02:05.0: PME# supported from D3hot D3cold
[ 0.429743] pci 0000:02:06.0: [1022:43c7] type 01 class 0x060400
[ 0.429743] pci 0000:02:06.0: enabling Extended Tags
[ 0.429743] pci 0000:02:06.0: PME# supported from D3hot D3cold
[ 0.429800] pci 0000:02:07.0: [1022:43c7] type 01 class 0x060400
[ 0.429912] pci 0000:02:07.0: enabling Extended Tags
[ 0.430025] pci 0000:02:07.0: PME# supported from D3hot D3cold
[ 0.430738] pci 0000:01:00.2: PCI bridge to [bus 02-08]
[ 0.435736] pci 0000:01:00.2: bridge window [io 0xf000-0xffff]
[ 0.435814] pci 0000:01:00.2: bridge window [mem 0xfcb00000-0xfccfffff]
[ 0.435921] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.436738] pci 0000:02:01.0: PCI bridge to [bus 04]
[ 0.436743] pci 0000:02:04.0: PCI bridge to [bus 05]
[ 0.436745] pci 0000:06:00.0: [8086:2526] type 00 class 0x028000
[ 0.436745] pci 0000:06:00.0: reg 0x10: [mem 0xfcc00000-0xfcc03fff 64bit]
[ 0.436864] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[ 0.437051] pci 0000:02:05.0: PCI bridge to [bus 06]
[ 0.437124] pci 0000:02:05.0: bridge window [mem 0xfcc00000-0xfccfffff]
[ 0.437732] pci 0000:02:06.0: PCI bridge to [bus 07]
[ 0.437738] pci 0000:08:00.0: [8086:1539] type 00 class 0x020000
[ 0.437738] pci 0000:08:00.0: reg 0x10: [mem 0xfcb00000-0xfcb1ffff]
[ 0.437738] pci 0000:08:00.0: reg 0x18: [io 0xf000-0xf01f]
[ 0.437738] pci 0000:08:00.0: reg 0x1c: [mem 0xfcb20000-0xfcb23fff]
[ 0.437902] pci 0000:08:00.0: PME# supported from D0 D3hot D3cold
[ 0.438090] pci 0000:02:07.0: PCI bridge to [bus 08]
[ 0.438161] pci 0000:02:07.0: bridge window [io 0xf000-0xffff]
[ 0.438238] pci 0000:02:07.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.438737] pci 0000:09:00.0: [2646:500e] type 00 class 0x010802
[ 0.438737] pci 0000:09:00.0: reg 0x10: [mem 0xfcf00000-0xfcf03fff 64bit]
[ 0.438744] pci 0000:00:02.2: PCI bridge to [bus 09]
[ 0.438744] pci 0000:00:02.2: bridge window [mem 0xfcf00000-0xfcffffff]
[ 0.438840] pci 0000:0a:00.0: [1002:1638] type 00 class 0x030000
[ 0.438924] pci 0000:0a:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.439013] pci 0000:0a:00.0: reg 0x18: [mem 0xe0000000-0xe01fffff 64bit pref]
[ 0.439100] pci 0000:0a:00.0: reg 0x20: [io 0xe000-0xe0ff]
[ 0.439176] pci 0000:0a:00.0: reg 0x24: [mem 0xfca00000-0xfca7ffff]
[ 0.439259] pci 0000:0a:00.0: enabling Extended Tags
[ 0.439359] pci 0000:0a:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.439455] pci 0000:0a:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:08.1 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.439737] pci 0000:0a:00.1: [1002:1637] type 00 class 0x040300
[ 0.439738] pci 0000:0a:00.1: reg 0x10: [mem 0xfca88000-0xfca8bfff]
[ 0.439834] pci 0000:0a:00.1: enabling Extended Tags
[ 0.439921] pci 0000:0a:00.1: PME# supported from D1 D2 D3hot D3cold
[ 0.440036] pci 0000:0a:00.2: [1022:15df] type 00 class 0x108000
[ 0.440122] pci 0000:0a:00.2: reg 0x18: [mem 0xfc900000-0xfc9fffff]
[ 0.440207] pci 0000:0a:00.2: reg 0x24: [mem 0xfca8c000-0xfca8dfff]
[ 0.440289] pci 0000:0a:00.2: enabling Extended Tags
[ 0.440743] pci 0000:0a:00.3: [1022:1639] type 00 class 0x0c0330
[ 0.440743] pci 0000:0a:00.3: reg 0x10: [mem 0xfc800000-0xfc8fffff 64bit]
[ 0.440743] pci 0000:0a:00.3: enabling Extended Tags
[ 0.440743] pci 0000:0a:00.3: PME# supported from D0 D3hot D3cold
[ 0.440768] pci 0000:0a:00.4: [1022:1639] type 00 class 0x0c0330
[ 0.440850] pci 0000:0a:00.4: reg 0x10: [mem 0xfc700000-0xfc7fffff 64bit]
[ 0.440948] pci 0000:0a:00.4: enabling Extended Tags
[ 0.441037] pci 0000:0a:00.4: PME# supported from D0 D3hot D3cold
[ 0.441737] pci 0000:0a:00.6: [1022:15e3] type 00 class 0x040300
[ 0.441737] pci 0000:0a:00.6: reg 0x10: [mem 0xfca80000-0xfca87fff]
[ 0.441737] pci 0000:0a:00.6: enabling Extended Tags
[ 0.441737] pci 0000:0a:00.6: PME# supported from D0 D3hot D3cold
[ 0.441743] pci 0000:00:08.1: PCI bridge to [bus 0a]
[ 0.441743] pci 0000:00:08.1: bridge window [io 0xe000-0xefff]
[ 0.441743] pci 0000:00:08.1: bridge window [mem 0xfc700000-0xfcafffff]
[ 0.441743] pci 0000:00:08.1: bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[ 0.441844] pci 0000:0b:00.0: [1022:7901] type 00 class 0x010601
[ 0.441939] pci 0000:0b:00.0: reg 0x24: [mem 0xfce01000-0xfce017ff]
[ 0.442021] pci 0000:0b:00.0: enabling Extended Tags
[ 0.442129] pci 0000:0b:00.0: 126.016 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x16 link at 0000:00:08.2 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
[ 0.442738] pci 0000:0b:00.1: [1022:7901] type 00 class 0x010601
[ 0.442738] pci 0000:0b:00.1: reg 0x24: [mem 0xfce00000-0xfce007ff]
[ 0.442738] pci 0000:0b:00.1: enabling Extended Tags
[ 0.442738] pci 0000:00:08.2: PCI bridge to [bus 0b]
[ 0.442738] pci 0000:00:08.2: bridge window [mem 0xfce00000-0xfcefffff]
[ 0.443066] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443174] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443277] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443386] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443491] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443591] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443692] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 7 10 11 14 15) *0
[ 0.443753] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 7 10 11 14 15) *0
[ 0.444745] iommu: Default domain type: Translated
[ 0.444747] pci 0000:0a:00.0: vgaarb: setting as boot VGA device
[ 0.444815] pci 0000:0a:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.444918] pci 0000:0a:00.0: vgaarb: bridge control possible
[ 0.444992] vgaarb: loaded
[ 0.445086] SCSI subsystem initialized
[ 0.445151] libata version 3.00 loaded.
[ 0.445151] ACPI: bus type USB registered
[ 0.445151] usbcore: registered new interface driver usbfs
[ 0.445151] usbcore: registered new interface driver hub
[ 0.445151] usbcore: registered new device driver usb
[ 0.445151] pps_core: LinuxPPS API ver. 1 registered
[ 0.445151] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 0.445749] PTP clock support registered
[ 0.445749] EDAC MC: Ver: 3.0.0
[ 0.445820] PCI: Using ACPI for IRQ routing
[ 0.448947] PCI: pci_cache_line_size set to 64 bytes
[ 0.448997] e820: reserve RAM buffer [mem 0x0009d400-0x0009ffff]
[ 0.448998] e820: reserve RAM buffer [mem 0x09c1f000-0x0bffffff]
[ 0.448999] e820: reserve RAM buffer [mem 0x0a200000-0x0bffffff]
[ 0.448999] e820: reserve RAM buffer [mem 0x0b000000-0x0bffffff]
[ 0.449000] e820: reserve RAM buffer [mem 0xb9e99000-0xbbffffff]
[ 0.449000] e820: reserve RAM buffer [mem 0xbe000000-0xbfffffff]
[ 0.449001] e820: reserve RAM buffer [mem 0x21e300000-0x21fffffff]
[ 0.449019] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.449088] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.451750] clocksource: Switched to clocksource tsc-early
[ 0.451854] FS-Cache: Loaded
[ 0.451924] pnp: PnP ACPI init
[ 0.452024] system 00:00: [mem 0xf0000000-0xf7ffffff] has been reserved
[ 0.452107] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.452135] system 00:01: [mem 0x220000000-0x23fffffff window] has been reserved
[ 0.452222] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.452263] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.452324] system 00:03: [io 0x0a00-0x0a2f] has been reserved
[ 0.452399] system 00:03: [io 0x0a30-0x0a3f] has been reserved
[ 0.452474] system 00:03: [io 0x0a40-0x0a4f] has been reserved
[ 0.452551] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.452658] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.452737] system 00:04: [io 0x040b] has been reserved
[ 0.452808] system 00:04: [io 0x04d6] has been reserved
[ 0.452878] system 00:04: [io 0x0c00-0x0c01] has been reserved
[ 0.452953] system 00:04: [io 0x0c14] has been reserved
[ 0.453024] system 00:04: [io 0x0c50-0x0c51] has been reserved
[ 0.453098] system 00:04: [io 0x0c52] has been reserved
[ 0.453169] system 00:04: [io 0x0c6c] has been reserved
[ 0.453239] system 00:04: [io 0x0c6f] has been reserved
[ 0.453319] system 00:04: [io 0x0cd8-0x0cdf] has been reserved
[ 0.453393] system 00:04: [io 0x0800-0x089f] has been reserved
[ 0.453468] system 00:04: [io 0x0b00-0x0b0f] has been reserved
[ 0.453543] system 00:04: [io 0x0b20-0x0b3f] has been reserved
[ 0.453618] system 00:04: [io 0x0900-0x090f] has been reserved
[ 0.453692] system 00:04: [io 0x0910-0x091f] has been reserved
[ 0.453767] system 00:04: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.453849] system 00:04: [mem 0xfec01000-0xfec01fff] could not be reserved
[ 0.453931] system 00:04: [mem 0xfedc0000-0xfedc0fff] has been reserved
[ 0.454011] system 00:04: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.454091] system 00:04: [mem 0xfed80000-0xfed8ffff] could not be reserved
[ 0.454173] system 00:04: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.454252] system 00:04: [mem 0xff000000-0xffffffff] has been reserved
[ 0.454336] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.454634] pnp: PnP ACPI: found 5 devices
[ 0.460024] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.460164] NET: Registered protocol family 2
[ 0.460380] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.460508] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.460659] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.460847] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.460965] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.461061] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.461196] NET: Registered protocol family 1
[ 0.461272] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.461349] pci 0000:02:01.0: PCI bridge to [bus 04]
[ 0.461425] pci 0000:02:04.0: PCI bridge to [bus 05]
[ 0.461503] pci 0000:02:05.0: PCI bridge to [bus 06]
[ 0.461574] pci 0000:02:05.0: bridge window [mem 0xfcc00000-0xfccfffff]
[ 0.461661] pci 0000:02:06.0: PCI bridge to [bus 07]
[ 0.461737] pci 0000:02:07.0: PCI bridge to [bus 08]
[ 0.461806] pci 0000:02:07.0: bridge window [io 0xf000-0xffff]
[ 0.461885] pci 0000:02:07.0: bridge window [mem 0xfcb00000-0xfcbfffff]
[ 0.461971] pci 0000:01:00.2: PCI bridge to [bus 02-08]
[ 0.462042] pci 0000:01:00.2: bridge window [io 0xf000-0xffff]
[ 0.462121] pci 0000:01:00.2: bridge window [mem 0xfcb00000-0xfccfffff]
[ 0.462206] pci 0000:00:02.1: PCI bridge to [bus 01-08]
[ 0.462277] pci 0000:00:02.1: bridge window [io 0xf000-0xffff]
[ 0.462354] pci 0000:00:02.1: bridge window [mem 0xfcb00000-0xfcdfffff]
[ 0.462437] pci 0000:00:02.2: PCI bridge to [bus 09]
[ 0.462508] pci 0000:00:02.2: bridge window [mem 0xfcf00000-0xfcffffff]
[ 0.462592] pci 0000:00:08.1: PCI bridge to [bus 0a]
[ 0.462661] pci 0000:00:08.1: bridge window [io 0xe000-0xefff]
[ 0.462738] pci 0000:00:08.1: bridge window [mem 0xfc700000-0xfcafffff]
[ 0.462820] pci 0000:00:08.1: bridge window [mem 0xd0000000-0xe01fffff 64bit pref]
[ 0.462909] pci 0000:00:08.2: PCI bridge to [bus 0b]
[ 0.462978] pci 0000:00:08.2: bridge window [mem 0xfce00000-0xfcefffff]
[ 0.463062] pci_bus 0000:00: resource 4 [io 0x0000-0x03af window]
[ 0.463139] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7 window]
[ 0.463215] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df window]
[ 0.463292] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff window]
[ 0.463369] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[ 0.463451] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[ 0.463533] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xfec2ffff window]
[ 0.463615] pci_bus 0000:00: resource 11 [mem 0xfee00000-0xffffffff window]
[ 0.463697] pci_bus 0000:01: resource 0 [io 0xf000-0xffff]
[ 0.463770] pci_bus 0000:01: resource 1 [mem 0xfcb00000-0xfcdfffff]
[ 0.463847] pci_bus 0000:02: resource 0 [io 0xf000-0xffff]
[ 0.463920] pci_bus 0000:02: resource 1 [mem 0xfcb00000-0xfccfffff]
[ 0.463997] pci_bus 0000:06: resource 1 [mem 0xfcc00000-0xfccfffff]
[ 0.464074] pci_bus 0000:08: resource 0 [io 0xf000-0xffff]
[ 0.464147] pci_bus 0000:08: resource 1 [mem 0xfcb00000-0xfcbfffff]
[ 0.464224] pci_bus 0000:09: resource 1 [mem 0xfcf00000-0xfcffffff]
[ 0.464302] pci_bus 0000:0a: resource 0 [io 0xe000-0xefff]
[ 0.464373] pci_bus 0000:0a: resource 1 [mem 0xfc700000-0xfcafffff]
[ 0.464451] pci_bus 0000:0a: resource 2 [mem 0xd0000000-0xe01fffff 64bit pref]
[ 0.464534] pci_bus 0000:0b: resource 1 [mem 0xfce00000-0xfcefffff]
[ 0.470458] pci 0000:0a:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.470562] pci 0000:0a:00.1: D0 power state depends on 0000:0a:00.0
[ 0.470754] PCI: CLS 64 bytes, default 64
[ 0.470835] Unpacking initramfsā¦
[ 8.989470] Freeing initrd memory: 144480K
[ 9.076757] pci 0000:00:00.2: AMD-Vi: IOMMU performance counters supported
[ 9.076950] pci 0000:00:00.2: canāt derive routing for PCI INT A
[ 9.077044] pci 0000:00:00.2: PCI INT A: not connected
[ 9.077162] pci 0000:00:01.0: Adding to iommu group 0
[ 9.077262] pci 0000:00:02.0: Adding to iommu group 1
[ 9.077356] pci 0000:00:02.1: Adding to iommu group 2
[ 9.077448] pci 0000:00:02.2: Adding to iommu group 3
[ 9.077551] pci 0000:00:08.0: Adding to iommu group 4
[ 9.077642] pci 0000:00:08.1: Adding to iommu group 4
[ 9.077737] pci 0000:00:08.2: Adding to iommu group 4
[ 9.077830] pci 0000:00:14.0: Adding to iommu group 5
[ 9.077918] pci 0000:00:14.3: Adding to iommu group 5
[ 9.078018] pci 0000:00:18.0: Adding to iommu group 6
[ 9.078104] pci 0000:00:18.1: Adding to iommu group 6
[ 9.078191] pci 0000:00:18.2: Adding to iommu group 6
[ 9.078277] pci 0000:00:18.3: Adding to iommu group 6
[ 9.078364] pci 0000:00:18.4: Adding to iommu group 6
[ 9.078450] pci 0000:00:18.5: Adding to iommu group 6
[ 9.078537] pci 0000:00:18.6: Adding to iommu group 6
[ 9.078623] pci 0000:00:18.7: Adding to iommu group 6
[ 9.078723] pci 0000:01:00.0: Adding to iommu group 7
[ 9.078818] pci 0000:01:00.1: Adding to iommu group 7
[ 9.078911] pci 0000:01:00.2: Adding to iommu group 7
[ 9.078998] pci 0000:02:00.0: Adding to iommu group 7
[ 9.079084] pci 0000:02:01.0: Adding to iommu group 7
[ 9.079170] pci 0000:02:04.0: Adding to iommu group 7
[ 9.079256] pci 0000:02:05.0: Adding to iommu group 7
[ 9.079342] pci 0000:02:06.0: Adding to iommu group 7
[ 9.079428] pci 0000:02:07.0: Adding to iommu group 7
[ 9.079516] pci 0000:06:00.0: Adding to iommu group 7
[ 9.079604] pci 0000:08:00.0: Adding to iommu group 7
[ 9.079690] pci 0000:09:00.0: Adding to iommu group 8
[ 9.079779] pci 0000:0a:00.0: Adding to iommu group 4
[ 9.079863] pci 0000:0a:00.1: Adding to iommu group 4
[ 9.079948] pci 0000:0a:00.2: Adding to iommu group 4
[ 9.080032] pci 0000:0a:00.3: Adding to iommu group 4
[ 9.080116] pci 0000:0a:00.4: Adding to iommu group 4
[ 9.080200] pci 0000:0a:00.6: Adding to iommu group 4
[ 9.080285] pci 0000:0b:00.0: Adding to iommu group 4
[ 9.080368] pci 0000:0b:00.1: Adding to iommu group 4
[ 9.082414] pci 0000:00:00.2: AMD-Vi: Found IOMMU cap 0x40
[ 9.082492] pci 0000:00:00.2: AMD-Vi: Extended features (0x206d73ef22254ade):
[ 9.082581] PPR X2APIC NX GT IA GA PC GA_vAPIC
[ 9.082652] AMD-Vi: Interrupt remapping enabled
[ 9.082720] AMD-Vi: Virtual APIC enabled
[ 9.082788] AMD-Vi: X2APIC enabled
[ 9.099400] AMD-Vi: Lazy IO/TLB flushing enabled
[ 9.100006] amd_uncore: 4 amd_df counters detected
[ 9.100093] amd_uncore: 6 amd_l3 counters detected
[ 9.100719] LVT offset 0 assigned for vector 0x400
[ 9.101001] perf: AMD IBS detected (0x000003ff)
[ 9.101087] perf/amd_iommu: Detected AMD IOMMU #0 (2 banks, 4 counters/bank).
[ 9.102426] workingset: timestamp_bits=40 max_order=21 bucket_order=0
[ 9.103093] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 9.103204] fuse: init (API version 7.32)
[ 9.105420] xor: automatically using best checksumming function avx
[ 9.105524] Key type asymmetric registered
[ 9.105601] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 9.105724] io scheduler mq-deadline registered
[ 9.105804] io scheduler kyber registered
[ 9.105888] io scheduler bfq registered
[ 9.106120] pcieport 0000:00:02.1: PME: Signaling with IRQ 26
[ 9.106296] pcieport 0000:00:02.2: PME: Signaling with IRQ 27
[ 9.106475] pcieport 0000:00:08.1: PME: Signaling with IRQ 28
[ 9.106678] pcieport 0000:00:08.2: PME: Signaling with IRQ 29
[ 9.107627] IPMI message handler: version 39.2
[ 9.107746] Monitor-Mwait will be used to enter C-1 state
[ 9.107751] ACPI: _PR.C000: Found 3 idle states
[ 9.108032] ACPI: _PR.C002: Found 3 idle states
[ 9.108482] ACPI: _PR.C004: Found 3 idle states
[ 9.108945] ACPI: _PR.C006: Found 3 idle states
[ 9.109211] ACPI: _PR.C008: Found 3 idle states
[ 9.109449] ACPI: _PR.C00A: Found 3 idle states
[ 9.109683] ACPI: _PR.C001: Found 3 idle states
[ 9.109911] ACPI: _PR.C003: Found 3 idle states
[ 9.110120] ACPI: _PR.C005: Found 3 idle states
[ 9.110326] ACPI: _PR.C007: Found 3 idle states
[ 9.110525] ACPI: _PR.C009: Found 3 idle states
[ 9.110727] ACPI: _PR.C00B: Found 3 idle states
[ 9.111111] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 9.112262] lp: driver loaded but no devices found
[ 9.112484] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 9.112600] AMD-Vi: AMD IOMMUv2 driver by Joerg Roedel [email protected]
[ 9.115373] loop: module loaded
[ 9.115541] Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 9.115652] db_root: cannot open: /etc/target
[ 9.115883] VFIO - User Level meta-driver version: 0.3
[ 9.116004] ehci_hcd: USB 2.0 āEnhancedā Host Controller (EHCI) Driver
[ 9.116089] ehci-pci: EHCI PCI platform driver
[ 9.116166] ohci_hcd: USB 1.1 āOpenā Host Controller (OHCI) Driver
[ 9.116251] ohci-pci: OHCI PCI platform driver
[ 9.116324] uhci_hcd: USB Universal Host Controller Interface driver
[ 9.116489] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 9.116566] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[ 9.171965] xhci_hcd 0000:01:00.0: hcc params 0x0200ef81 hci version 0x110 quirks 0x0000000000000410
[ 9.172490] hub 1-0:1.0: USB hub found
[ 9.172583] hub 1-0:1.0: 10 ports detected
[ 9.172928] xhci_hcd 0000:01:00.0: xHCI Host Controller
[ 9.173019] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[ 9.173123] xhci_hcd 0000:01:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[ 9.173259] usb usb2: We donāt know the algorithms for LPM for this host, disabling LPM.
[ 9.173438] hub 2-0:1.0: USB hub found
[ 9.173520] hub 2-0:1.0: 4 ports detected
[ 9.173640] usb: port power management may be unreliable
[ 9.173885] xhci_hcd 0000:0a:00.3: xHCI Host Controller
[ 9.173974] xhci_hcd 0000:0a:00.3: new USB bus registered, assigned bus number 3
[ 9.174159] xhci_hcd 0000:0a:00.3: hcc params 0x0268ffe5 hci version 0x110 quirks 0x0000000000000410
[ 9.174607] hub 3-0:1.0: USB hub found
[ 9.174685] hub 3-0:1.0: 4 ports detected
[ 9.174953] xhci_hcd 0000:0a:00.3: xHCI Host Controller
[ 9.175041] xhci_hcd 0000:0a:00.3: new USB bus registered, assigned bus number 4
[ 9.175145] xhci_hcd 0000:0a:00.3: Host supports USB 3.1 Enhanced SuperSpeed
[ 9.175254] usb usb4: We donāt know the algorithms for LPM for this host, disabling LPM.
[ 9.175434] hub 4-0:1.0: USB hub found
[ 9.175511] hub 4-0:1.0: 2 ports detected
[ 9.175711] xhci_hcd 0000:0a:00.4: xHCI Host Controller
[ 9.175810] xhci_hcd 0000:0a:00.4: new USB bus registered, assigned bus number 5
[ 9.175991] xhci_hcd 0000:0a:00.4: hcc params 0x0268ffe5 hci version 0x110 quirks 0x0000000000000410
[ 9.176434] hub 5-0:1.0: USB hub found
[ 9.176516] hub 5-0:1.0: 4 ports detected
[ 9.176710] xhci_hcd 0000:0a:00.4: xHCI Host Controller
[ 9.176806] xhci_hcd 0000:0a:00.4: new USB bus registered, assigned bus number 6
[ 9.176904] xhci_hcd 0000:0a:00.4: Host supports USB 3.1 Enhanced SuperSpeed
[ 9.177007] usb usb6: We donāt know the algorithms for LPM for this host, disabling LPM.
[ 9.177182] hub 6-0:1.0: USB hub found
[ 9.177259] hub 6-0:1.0: 2 ports detected
[ 9.177457] usbcore: registered new interface driver usb-storage
[ 9.177563] i8042: PNP: No PS/2 controller found.
[ 9.177670] mousedev: PS/2 mouse device common for all mice
[ 9.177819] usbcore: registered new interface driver synaptics_usb
[ 9.177938] input: PC Speaker as /devices/platform/pcspkr/input/input0
[ 9.178074] rtc_cmos 00:02: RTC can wake from S4
[ 9.178322] rtc_cmos 00:02: registered as rtc0
[ 9.178463] rtc_cmos 00:02: setting system clock to 2022-02-19T22:16:52 UTC (1645309012)
[ 9.178577] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 9.178693] IR NEC protocol handler initialized
[ 9.178771] IR RC5(x/sz) protocol handler initialized
[ 9.178845] IR RC6 protocol handler initialized
[ 9.178914] IR JVC protocol handler initialized
[ 9.178983] IR Sony protocol handler initialized
[ 9.179052] IR SANYO protocol handler initialized
[ 9.179122] IR Sharp protocol handler initialized
[ 9.179192] IR MCE Keyboard/mouse protocol handler initialized
[ 9.179270] IR XMP protocol handler initialized
[ 9.179355] hid: raw HID events driver (C) Jiri Kosina
[ 9.179640] usbcore: registered new interface driver usbhid
[ 9.179724] usbhid: USB HID core driver
[ 9.179870] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 9.180018] gre: GRE over IPv4 demultiplexor driver
[ 9.180089] ip_gre: GRE over IPv4 tunneling driver
[ 9.180265] IPv4 over IPsec tunneling driver
[ 9.180370] Initializing XFRM netlink socket
[ 9.180488] NET: Registered protocol family 10
[ 9.180737] Segment Routing with IPv6
[ 9.180849] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 9.181008] NET: Registered protocol family 17
[ 9.181084] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 9.181220] 8021q: 802.1Q VLAN Support v1.8
[ 9.181299] 9pnet: Installing 9P2000 support
[ 9.181368] Key type dns_resolver registered
[ 9.181464] NET: Registered protocol family 40
[ 9.182104] microcode: CPU0: patch_level=0x0a50000c
[ 9.182177] microcode: CPU1: patch_level=0x0a50000c
[ 9.182253] microcode: CPU2: patch_level=0x0a50000c
[ 9.182329] microcode: CPU3: patch_level=0x0a50000c
[ 9.182405] microcode: CPU4: patch_level=0x0a50000c
[ 9.182479] microcode: CPU5: patch_level=0x0a50000c
[ 9.182553] microcode: CPU6: patch_level=0x0a50000c
[ 9.182625] microcode: CPU7: patch_level=0x0a50000c
[ 9.182698] microcode: CPU8: patch_level=0x0a50000c
[ 9.182769] microcode: CPU9: patch_level=0x0a50000c
[ 9.188650] microcode: CPU10: patch_level=0x0a50000c
[ 9.188723] microcode: CPU11: patch_level=0x0a50000c
[ 9.188862] microcode: Microcode Update Driver: v2.2.
[ 9.188866] IPI shorthand broadcast: enabled
[ 9.189005] sched_clock: Marking stable (9165296593, 23558527)->(9206695233, -17840113)
[ 9.189169] registered taskstats version 1
[ 9.189333] Btrfs loaded, crc32c=crc32c-generic
[ 9.502005] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ 9.555999] usb 1-10: new full-speed USB device number 2 using xhci_hcd
[ 9.632220] usb-storage 5-1:1.0: USB Mass Storage device detected
[ 9.632484] scsi host0: usb-storage 5-1:1.0
[ 10.147994] tsc: Refined TSC clocksource calibration: 3892.686 MHz
[ 10.148100] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x7038b8db878, max_idle_ns: 881590710692 ns
[ 10.148308] clocksource: Switched to clocksource tsc
[ 10.660801] scsi 0:0:0:0: Direct-Access SanDiskā Cruzer Fit 1.00 PQ: 0 ANSI: 6
[ 10.661083] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 10.661433] sd 0:0:0:0: [sda] 30031872 512-byte logical blocks: (15.4 GB/14.3 GiB)
[ 10.662633] sd 0:0:0:0: [sda] Write Protect is off
[ 10.662719] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 10.663000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesnāt support DPO or FUA
[ 10.668304] sda: sda1
[ 10.669473] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 12.131986] floppy0: no floppy controllers found
[ 12.132598] Freeing unused kernel image (initmem) memory: 1120K
[ 12.139035] Write protecting the kernel read-only data: 16384k
[ 12.139645] Freeing unused kernel image (text/rodata gap) memory: 2044K
[ 12.140124] Freeing unused kernel image (rodata/data gap) memory: 1748K
[ 12.140231] rodata_test: all tests were successful
[ 12.140318] Run /init as init process
[ 12.140389] with arguments:
[ 12.140389] /init
[ 12.140390] with environment:
[ 12.140391] HOME=/
[ 12.140391] TERM=linux
[ 12.140391] BOOT_IMAGE=/bzimage
[ 12.183740] random: udevd: uninitialized urandom read (16 bytes read)
[ 12.183874] random: udevd: uninitialized urandom read (16 bytes read)
[ 12.183973] random: udevd: uninitialized urandom read (16 bytes read)
[ 12.184957] udevd[1373]: starting eudev-3.2.5
[ 12.368304] random: fast init done
[ 13.218115] random: crng init done
[ 13.218188] random: 6 urandom warning(s) missed due to ratelimiting
[ 14.033330] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[ 14.035221] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[ 14.262828] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 14.262977] ACPI: Power Button [PWRB]
[ 14.263067] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 14.266816] ACPI: Power Button [PWRF]
[ 14.328756] acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
[ 14.376862] ACPI: Video Device [VGA1] (multi-head: yes rom: no post: no)
[ 14.377080] ccp 0000:0a:00.2: ccp: unable to access the device: you might be running a broken BIOS.
[ 14.377406] acpi device:16: registered as cooling_device12
[ 14.377572] ahci 0000:01:00.1: version 3.0
[ 14.377573] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:15/LNXVIDEO:01/input/input3
[ 14.378253] ahci 0000:01:00.1: SSS flag set, parallel bus scan disabled
[ 14.378415] ahci 0000:01:00.1: AHCI 0001.0301 32 slots 8 ports 6 Gbps 0x33 impl SATA mode
[ 14.378540] ahci 0000:01:00.1: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part sxs deso sadm sds apst
[ 14.378842] RAPL PMU: API unit is 2^-32 Joules, 1 fixed counters, 163840 ms ovfl timer
[ 14.378978] RAPL PMU: hw unit of domain package 2^-16 Joules
[ 14.379892] scsi host1: ahci
[ 14.380139] scsi host2: ahci
[ 14.380380] scsi host3: ahci
[ 14.380596] scsi host4: ahci
[ 14.380919] scsi host5: ahci
[ 14.381145] scsi host6: ahci
[ 14.381385] scsi host7: ahci
[ 14.381597] scsi host8: ahci
[ 14.381712] ata1: SATA max UDMA/133 abar m131072@0xfcd80000 port 0xfcd80100 irq 67
[ 14.381817] ata2: SATA max UDMA/133 abar m131072@0xfcd80000 port 0xfcd80180 irq 67
[ 14.381914] ata3: DUMMY
[ 14.381971] ata4: DUMMY
[ 14.382028] ata5: SATA max UDMA/133 abar m131072@0xfcd80000 port 0xfcd80300 irq 67
[ 14.382126] ata6: SATA max UDMA/133 abar m131072@0xfcd80000 port 0xfcd80380 irq 67
[ 14.382222] ata7: DUMMY
[ 14.382277] ata8: DUMMY
[ 14.382605] ahci 0000:0b:00.0: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 14.382709] ahci 0000:0b:00.0: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 14.383045] scsi host9: ahci
[ 14.383164] ata9: SATA max UDMA/133 abar m2048@0xfce01000 port 0xfce01100 irq 69
[ 14.383439] ahci 0000:0b:00.1: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
[ 14.383541] ahci 0000:0b:00.1: flags: 64bit ncq sntf ilck pm led clo only pmp fbs pio slum part
[ 14.384024] scsi host10: ahci
[ 14.384145] ata10: SATA max UDMA/133 abar m2048@0xfce00000 port 0xfce00100 irq 71
[ 14.387562] ccp 0000:0a:00.2: tee enabled
[ 14.387630] ccp 0000:0a:00.2: psp enabled
[ 14.393803] nvme nvme0: pci function 0000:09:00.0
[ 14.416786] nvme nvme0: allocated 64 MiB host memory buffer.
[ 14.429870] cryptd: max_cpu_qlen set to 1000
[ 14.430052] ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B08 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0F (\GSA1.SMBI) (20200925/utaddress-204)
[ 14.430258] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 14.438660] nvme nvme0: 8/0/0 default/read/poll queues
[ 14.440657] nvme0n1: p1
[ 14.478375] igb: Intel(R) Gigabit Ethernet Network Driver
[ 14.478468] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 14.485156] AVX2 version of gcm_enc/dec engaged.
[ 14.485250] AES CTR mode by8 optimization enabled
[ 14.507704] pps pps0: new PPS source ptp0
[ 14.507919] igb 0000:08:00.0: added PHC on eth0
[ 14.508009] igb 0000:08:00.0: Intel(R) Gigabit Ethernet Network Connection
[ 14.508118] igb 0000:08:00.0: eth0: (PCIe:2.5Gb/s:Width x1) b4:2e:99:cc:ae:21
[ 14.508229] igb 0000:08:00.0: eth0: PBA No: FFFFFF-0FF
[ 14.508320] igb 0000:08:00.0: Using MSI-X interrupts. 2 rx queue(s), 2 tx queue(s)
[ 14.546207] Bluetooth: Core ver 2.22
[ 14.546344] NET: Registered protocol family 31
[ 14.546437] Bluetooth: HCI device and connection manager initialized
[ 14.546537] Bluetooth: HCI socket layer initialized
[ 14.546603] kvm: Nested Virtualization enabled
[ 14.546620] Bluetooth: L2CAP socket layer initialized
[ 14.546722] SVM: kvm: Nested Paging enabled
[ 14.546820] Bluetooth: SCO socket layer initialized
[ 14.546893] SVM: Virtual VMLOAD VMSAVE supported
[ 14.547074] SVM: Virtual GIF supported
[ 14.560773] usbcore: registered new interface driver btusb
[ 14.564950] Bluetooth: hci0: Firmware revision 0.1 build 168 week 48 2020
[ 14.576169] MCE: In-kernel MCE decoding enabled.
[ 14.689360] ata10: SATA link down (SStatus 0 SControl 300)
[ 14.689528] ata9: SATA link down (SStatus 0 SControl 300)
[ 14.844033] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 14.853080] ata1.00: ATA-9: WDC WD100EFAX-68LHPN0, 1EHU83MZ, 83.H0A83, max UDMA/133
[ 14.853203] ata1.00: 19532873728 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 14.868506] ata1.00: configured for UDMA/133
[ 14.868861] scsi 1:0:0:0: Direct-Access ATA WDC WD100EFAX-68 0A83 PQ: 0 ANSI: 5
[ 14.869387] sd 1:0:0:0: [sdb] 19532873728 512-byte logical blocks: (10.0 TB/9.10 TiB)
[ 14.869396] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 14.869510] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 14.869722] sd 1:0:0:0: [sdb] Write Protect is off
[ 14.869831] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 14.869877] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesnāt support DPO or FUA
[ 14.941410] sdb: sdb1
[ 14.942063] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 15.332000] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 15.341353] ata2.00: ATA-9: WDC WD140EFGX-68B0GN0, Y6G2UPNC, 85.00A85, max UDMA/133
[ 15.341465] ata2.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 15.360479] ata2.00: configured for UDMA/133
[ 15.360717] scsi 2:0:0:0: Direct-Access ATA WDC WD140EFGX-68 0A85 PQ: 0 ANSI: 5
[ 15.361053] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 15.361525] sd 2:0:0:0: [sdc] 27344764928 512-byte logical blocks: (14.0 TB/12.7 TiB)
[ 15.361639] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 15.361740] sd 2:0:0:0: [sdc] Write Protect is off
[ 15.361822] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 15.361839] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesnāt support DPO or FUA
[ 15.431134] sdc: sdc1
[ 15.431763] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 15.673656] ata5: SATA link down (SStatus 0 SControl 330)
[ 16.140032] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 16.141276] ata6.00: ATA-10: WDC WD40EZRZ-75GXCB0, WD-WCC7K3TYNN5C, 80.00A80, max UDMA/133
[ 16.141423] ata6.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 16.142650] ata6.00: configured for UDMA/133
[ 16.143003] scsi 6:0:0:0: Direct-Access ATA WDC WD40EZRZ-75G 0A80 PQ: 0 ANSI: 5
[ 16.143508] sd 6:0:0:0: [sdd] 7814037168 512-byte logical blocks: (4.00 TB/3.64 TiB)
[ 16.143628] sd 6:0:0:0: [sdd] 4096-byte physical blocks
[ 16.143630] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 16.143717] sd 6:0:0:0: [sdd] Write Protect is off
[ 16.150241] sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 16.150289] sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesnāt support DPO or FUA
[ 16.617935] sdd: sdd1
[ 16.618399] sd 6:0:0:0: [sdd] Attached SCSI disk
[ 17.510484] 8021q: adding VLAN 0 to HW filter on device eth0
[ 20.455568] igb 0000:08:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 77.863416] Linux agpgart interface v0.103
[ 77.883575] nvidia: loading out-of-tree module taints kernel.
[ 77.883582] nvidia: module license āNVIDIAā taints kernel.
[ 77.883582] Disabling lock debugging due to kernel taint
[ 77.902229] nvidia-nvlink: Nvlink Core is being initialized, major device number 245
[ 77.902233] NVRM: No NVIDIA GPU found.
[ 77.903144] nvidia-nvlink: Unregistered the Nvlink Core, major device number 245
[ 80.174692] md: unRAID driver 2.9.17 installed
[ 80.187327] mdcmd (1): import 0
[ 80.187330] md: import_slot: 0 empty
[ 80.187680] mdcmd (2): import 1 sdb 64 9766436812 0 WDC_WD100EFAX-68LHPN0_1EHU83MZ
[ 80.187685] md: import disk1: (sdb) WDC_WD100EFAX-68LHPN0_1EHU83MZ size: 9766436812
[ 80.187949] mdcmd (3): import 2 sdd 64 3907018532 0 WDC_WD40EZRZ-75GXCB0_WD-WCC7K3TYNN5C
[ 80.187953] md: import disk2: (sdd) WDC_WD40EZRZ-75GXCB0_WD-WCC7K3TYNN5C size: 3907018532
[ 80.188269] mdcmd (4): import 3 sdc 64 13672382412 0 WDC_WD140EFGX-68B0GN0_Y6G2UPNC
[ 80.188273] md: import disk3: (sdc) WDC_WD140EFGX-68B0GN0_Y6G2UPNC size: 13672382412
[ 80.188286] mdcmd (5): import 4
[ 80.188295] mdcmd (6): import 5
[ 80.188304] mdcmd (7): import 6
[ 80.188312] mdcmd (8): import 7
[ 80.188318] mdcmd (9): import 8
[ 80.188326] mdcmd (10): import 9
[ 80.188334] mdcmd (11): import 10
[ 80.188341] mdcmd (12): import 11
[ 80.188347] mdcmd (13): import 12
[ 80.188353] mdcmd (14): import 13
[ 80.188358] mdcmd (15): import 14
[ 80.188365] mdcmd (16): import 15
[ 80.188371] mdcmd (17): import 16
[ 80.188378] mdcmd (18): import 17
[ 80.188385] mdcmd (19): import 18
[ 80.188392] mdcmd (20): import 19
[ 80.188398] mdcmd (21): import 20
[ 80.188404] mdcmd (22): import 21
[ 80.188410] mdcmd (23): import 22
[ 80.188417] mdcmd (24): import 23
[ 80.188424] mdcmd (25): import 24
[ 80.188430] mdcmd (26): import 25
[ 80.188443] mdcmd (27): import 26
[ 80.188449] mdcmd (28): import 27
[ 80.188455] mdcmd (29): import 28
[ 80.188460] mdcmd (30): import 29
[ 80.188461] md: import_slot: 29 empty
[ 84.562208] mdcmd (31): set md_num_stripes 1280
[ 84.562214] mdcmd (32): set md_queue_limit 80
[ 84.562217] mdcmd (33): set md_sync_limit 5
[ 84.562219] mdcmd (34): set md_write_method
[ 84.562237] mdcmd (35): start STOPPED
[ 84.562575] unraid: allocating 25990K for 1280 stripes (5 disks)
[ 84.566979] md1: running, size: 9766436812 blocks
[ 84.567056] md2: running, size: 3907018532 blocks
[ 84.567121] md3: running, size: 13672382412 blocks
[ 84.866888] mdcmd (36): stop
[ 84.866898] md1: stopping
[ 84.874882] md2: stopping
[ 84.885805] md3: stopping
[ 112.780391] mdcmd (37): set md_num_stripes 1280
[ 112.780404] mdcmd (38): set md_queue_limit 80
[ 112.780411] mdcmd (39): set md_sync_limit 5
[ 112.780417] mdcmd (40): set md_write_method
[ 112.780443] mdcmd (41): start STOPPED
[ 112.780964] unraid: allocating 25990K for 1280 stripes (5 disks)
[ 112.785257] md1: running, size: 9766436812 blocks
[ 112.785336] md2: running, size: 3907018532 blocks
[ 112.785409] md3: running, size: 13672382412 blocks
[ 113.335236] SGI XFS with ACLs, security attributes, no debug enabled
[ 113.336121] XFS (md1): Mounting V5 Filesystem
[ 113.487997] XFS (md1): Ending clean mount
[ 113.608561] xfs filesystem being mounted at /mnt/disk1 supports timestamps until 2038 (0x7fffffff)
[ 113.618399] XFS (md2): Mounting V5 Filesystem
[ 114.225078] XFS (md2): Ending clean mount
[ 114.266785] xfs filesystem being mounted at /mnt/disk2 supports timestamps until 2038 (0x7fffffff)
[ 114.276362] XFS (md3): Mounting V5 Filesystem
[ 114.439964] XFS (md3): Ending clean mount
[ 114.586153] xfs filesystem being mounted at /mnt/disk3 supports timestamps until 2038 (0x7fffffff)
[ 114.596816] XFS (nvme0n1p1): Mounting V5 Filesystem
[ 114.604802] XFS (nvme0n1p1): Ending clean mount
[ 114.606689] xfs filesystem being mounted at /mnt/cache supports timestamps until 2038 (0x7fffffff)
[ 115.308922] dev[00000000d3c0c258]: Unable to change SE Device alua_support: alua_support has fixed value
[ 115.308927] dev[00000000d3c0c258]: Unable to change SE Device alua_support: alua_support has fixed value
[ 115.309036] ignoring deprecated emulate_dpo attribute
[ 115.309059] ignoring deprecated emulate_fua_read attribute
[ 115.309385] dev[00000000d3c0c258]: Unable to change SE Device pgr_support: pgr_support has fixed value
[ 115.309389] dev[00000000d3c0c258]: Unable to change SE Device pgr_support: pgr_support has fixed value
[ 117.775948] BTRFS: device fsid 91383b07-5910-47d9-a58b-f3f73a873310 devid 1 transid 6272 /dev/loop2 scanned by udevd (4595)
[ 117.776354] BTRFS info (device loop2): using free space tree
[ 117.776355] BTRFS info (device loop2): has skinny extents
[ 117.781957] BTRFS info (device loop2): enabling ssd optimizations
[ 117.986252] Bridge firewalling registered
[ 119.105770] 8021q: adding VLAN 0 to HW filter on device shim-eth0
[ 204.078480] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
above that it looks like the pci express card. can be bios or kernel. did you already update the kernel? But this kinda points to IOMMU problems and i didnāt have trouble with that so i donāt have experience there
and its not showming up is lspci i asume ?
There is a newer BIOS update for your board. Iām not overly confident it will solve your issue, but none the less should be installed to rule out the possibility.
@mfdoom7 maybe updating the firmware of the pci card on a different machine. or taking a look at the kernel of unraid mayebe a fresh compile
@Mongoosh its not only 1 card every 8x and 4x does not work. my 4x nic also dont work but when switch cpu it works.
did you try an other os ? If you look at the error is dmesg and google them all solutions point in direction of firmware. or drivers.
@Mongoosh Update: F63a AGESA V2 1.2.0.6 B makes my nic work. this bios just rolled out.
x4 pci-e works now on gigabyte I aorus pro wifi !
x8 still does not work !
but its a beta bios so fingers crossed.