AMD FX-8350 Strange Tempreture And Prime95 Temps?

Alright so lets start this off with my rig

http://uk.pcpartpicker.com/user/Matthew12106/saved/2GHS

 

So this is a fairly new build i built 2 months ago ( my first build) And i want to see what the cpu temps were like so i fired up core temp and openhardware monitor and i was getting some strange temps like 8 20 15 17 and really low temps and im like wut... the room is not even that cold how? So make sure everything was ok and to see how my 8350 was doing under my hyper 212 evo i fired up prime 95 and did a torture test under

In Place Large FFTs(Maximum heat power comsumption some ram tested)

So after a min and a half and stuff i hit like 45 which is fine and it didnt really move moving about 1 degree per min so at 5 mins it was 46-7 and but at 3:30 something interesting happened with core 6 as you can see

http://i.imgur.com/QB3vSUM.jpg

so i'm like wuuuuut anyway at 5 mins it was pretty much the same temp but that was not the thing worrying me it was that message 

POSSIBLE HARDWARE FAILURE, CONSULT README.TXT FILE, RESTARTING TEST

ERROR: ILLEGAL SUMOUT

 

What did this mean and from there minutes on out the load on that core was like 50-60% compared to the others at 100%

And then later the same thing happened to core 5 wtf whats happening.

 

anyway at 11 mins the temp was like 47 and here was the image after 11 mins 

http://i.imgur.com/RFNuAvt.jpg

So 47 is not bad after 11 mins anyway please tell me

What is with those crazy idealing temps

the prime95 error

and also another weird thing was that about 5 seconds after the test was closed the temp went to like 21... how is that possible?

 

Cheers for the help

are you overclocked? if not could be bad memory. you should test your memory, if not then you might have a bad cpu.

well i have the same setup but i use the stock cooler, so mines idleing warmer, anyway you have a failure on core 6. i used prime95 long time ago for an hour, and i did not had any core failures, but i did some settings in Ai tweaker, cpu core voltage from offset to manual mode, let everything on auto, and i disabled cool n quiet. so my cpu runs constantly at 4.1GHZ. the only thing i notice, is that your cpu runs at 4.3GHZ at 1.325V,  mines is running at 1.368V maybe you can try to set the cpu core voltage to manual mode in the bios, and disable cool n quiet, look if the still get the core failure, on core 6.

im not overclocked

 

oh shit i have a core failure on 6? what about 5 cause it showed the same message and what does that mean are they completly unfunctional and it said poissle hardware failure... oh shit

 

gonna try run it again

 

yup same thing number 5 failed but in the log it has a bunch of those messages and then it says under them when i extended it 

Maximum number of warnings exceeded

torture test completed 1 tests in 3 minutes - 0 erros, 100 warnings.

worker stoped

wtf did the same thing in number 8

.... Torture test completed 8 tests in 13 minutes - 0 errors, 100 warnings

 

Do not worry about the FX series idle temps. AMD is known to have bad thermal sensors. My FX6350 idles around 6C or about 13less than ambient (It's lying to me)

I find that their thermal sensors are not accurate until 25%+ load.

 

I have the FX6350 which is basically a 8350 but without the two other cores. same arch and everything.

Prime is a violent program, have you tried using other programs to see if cores 5 and 6 do the same thing? If the problem is only in prime than there is probably no problem because no real world application will be able to recreate prime.

Ran the test for 1/2 an hour it was yes core 5 and 8 that failed this time core 6 was fine... idk at this point im going to take this other persons advice and use another program

 

any recommendations for programs. and in the test i just did 6 was fine it core 5 and 8 this time >.<

 

aida64 is one i know off the top of my head- anyone know of some others?

cheers mate i'll download it and see what happens

 

ok been running the system stabilty test for 5 mins now seems fine.. although it says the cores selected are

Cpu #1 / Core#1

Cpu #1 / Core#2

Cpu #1 / Core#3

Cpu #1 / Core#4

 

Although in programs it says all the cores are on full load so not 2 sure about that anyway it's running im not sure if the core fails how im supposed to know maybe it pops up or something but idk ill see

 

weird. i know aida is pay to play tho. so maybe in the full registered version you have to pay up the waaaazooo

 

nah it loaded them all it just didnt display all of them

did it for 15 mins seems fine gonna call it quits for today

cheers mate

 

that's super.

Dude, why is your CPU bus at 217? WHY???

This adjustment will also affect stability of NB and Memory... Who or what did this?